Using the fluent program in the porous media
Dear Dr Omer,
you can add porous media for Darcy and Non-Darcy flow in FLUENT.
Please see the PDF below
https://www.google.iq/url?sa=t&rct=j&q=&esrc=s&source=web&cd=3&cad=rja&uact=8&ved=0ahUKEwi1ntWjn-PYAhXIkCwKHSh5DbYQFgg4MAI&url=http%3A%2F%2Fwww.ara.bme.hu%2Fneptun%2FBMEGEATMW03%2F2013-2014-II%2Flaboratory%2FH06_BMW-AIRFILTER%2FANSYS-Fluent_723_porousmediacondition_see-page14-15.pdf&usg=AOvVaw3UWRJlseBy24ssX1BoSy29
https://www.google.iq/url?sa=t&rct=j&q=&esrc=s&source=web&cd=4&cad=rja&uact=8&ved=0ahUKEwi1ntWjn-PYAhXIkCwKHSh5DbYQFgg9MAM&url=http%3A%2F%2Fdl.mr-cfd.com%2Ftutorials%2Fansys-fluent%2Fporous-media-simulation.pdf&usg=AOvVaw10eLETBwHc2PanItzyfTD1
Regards
Convective heat transfer should be coulped with Darcy Law.
http://www.ara.bme.hu/neptun/BMEGEATMW03/2013-2014-II/laboratory/H06_BMW-AIRFILTER/ANSYS-Fluent_723_porousmediacondition_see-page14-15.pdf
For different type of solar cell
01 February 2018 5,061 0 View
Solar pond
05 June 2017 6,019 0 View
i need any data
05 June 2017 8,592 0 View
Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...
25 July 2024 2,309 5 View
I had a problem for so long. I could easily delete elements in ABAQUS implicit solver but I needed to use VUMAT so I had to have Explicit solution but the element did not disappear for so long. I...
23 July 2024 10,032 0 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....
07 July 2024 1,182 8 View
hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.
03 July 2024 5,418 4 View
i have attached my model and i have used point based mesh independent fastener using attachment points and type of connector is basic cartesian but this is not working as i apply displacement on...
02 July 2024 6,293 0 View
Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."
30 June 2024 7,894 1 View
The underlying idea behind the environmental Kuznets curve is that GDP per capita initially increases environmental degradation but later reduces the environmental degradation as the result of the...
28 June 2024 949 0 View
hi im performing IDA for a 30 story consisting of bearing wall system of special shear walls for gravity and lateral resisting system , i usually face convergence problems with that , the walls...
27 June 2024 9,492 0 View
I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...
26 June 2024 2,358 0 View