I would like to model three dimensional water absorption in a Glass-Epoxy composite with considering the effect of temperature and orientation of fibers using Abaqus. Do you have an idea?
Thanks Soheil. The references you provided are helpful.
Most of journals require for paper submission to suggest three or four reviewers. How to choose them ? Is it among the authors of the papers cited in your manuscript, among the members of the...
08 September 2019 5,482 3 View
Hi, I want to model E-glass/Epoxy damage in SHPB test using a Hashin 3D creterion VUMAT but I faced the problem of elements distortion "ErrElemExcessDistortion-Step1 have distorted excessively"....
05 June 2018 3,731 9 View
Hi everyone, I want to know the best way to write a coherent literature review for my PhD dissertation without being lost in reading articles. Regards, Larbi
06 July 2016 5,801 16 View
Hi,I want to know what is the CPU time for a Job when it is submitted with other jobs on I7 Laptop. The TOTAL CPU TIME that we get in the end of Data file is it for one core (not for the eight...
09 October 2015 2,575 1 View
I want to reproduce the experimental stress-strain curves numerically using abaqus. Have you an idea ?
09 October 2015 7,316 2 View
Hi,Is there a direct way to reproduce numerically in Abaqus the strain recorded by a full Wheatstone bridge measuring the Poisson’s effect as in SHPB bars.Thanks
09 October 2015 5,859 5 View
How can I measure the 9 engineering constants for laminate layers using DIC to introduce them to Abaqus for SHPB dynamic behavior modeling?
11 December 2014 4,405 2 View
During impact in SHPB tests, an increase in temperature was observed. The dissipated energy affects the viscoelastic behavior of composites especially when the released temperature attains the Tg...
11 December 2014 9,555 7 View
I want to model damage of Glass-Epoxy composite under impact using Abaqus. Does anyone implemented a failure criterion such as puck or Matzenmiller ones in a VUMAT for Abaqus/Explicit or used...
11 December 2014 2,721 3 View
Pulse shaper for composites high strain rates.
04 May 2014 9,153 2 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...
08 August 2024 4,831 4 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View