Which nonlinear optical processes lead to multiple wavelength conversion in single period PPLN?

I have performed an experiment to frequency mix 974 nm LD laser and a C-band ASE laser source in a single period (10.2 um) MgO:PPLN. I however noticed five peaks at 487, 536, 598, 756, and 816 nm...

08 September 2018 9,767 8 View

How do I measure the splitting ratio of proton exchanged Y-junction waveguide?

02 March 2017 8,219 6 View

Can someone help me plot the attached Fourier series using Matlab code?

I need a Matlab code to plot a rectangular wave function with a constant period and normalized amplitude. Please see the attached exponential Fourier series. Thank you in advance.

01 February 2017 9,888 4 View

How does magnetic field influence poling of lithium niobate/tantalate?

10 November 2016 4,389 0 View

How do I correct the error in the matlab code?

I have a simple matlab code for plotting a Y-junction but it can't run. Any one with matlab knowledge can please advice me on the attached code.

31 December 2015 1,160 10 View

Can anybody share modeling parameters in COMSOL Multiphysics for Mach-Zehnder interferometer or y-junction design?

COMSOL Multiphysics 5.2 (and above) has a solved Mach-zehnder interferometer in its model library for which part of its geometry is S-shape. I am using version 4.3b which doesn't have that...

31 December 2015 8,915 2 View

How do I design a Y-junction using comsol multiphysics or matlab?

Y-branch waveguide structures are fundamental elements of integrated optics devices such as power or optical splitters, power or optical combiners, integrated-optic gyroscopes, Mach-Zehnder...

31 December 2015 7,947 5 View

Which is the best simulation setup using VPI TransmissionMaker before field testing?

I am investigating the influence of different modulation formats on gain flatness of raman assisted fibre optical parametric amplifiers.

31 December 2014 7,236 2 View

wind and solar energy

can someone help me on how to use available wind velocity data to design a specification of a wind turbine generator

02 March 2010 6,956 4 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View