How can I find the cross sectional area and volume of a single effect submerged evaporator?

Vishnuvardhan Tanga @Vishnuvardhan-Tanga

24 April 2020 0 4K Report

Can someone tell me is there any formula to calculate the Cross sectional area and volume of a single effect submerged evaporator.

With regards

Badges
Science topic

More Vishnuvardhan Tanga's questions See All

Overall heat transfer coefficient of superheater?

Hello, I am modelling a superheater in simulink. Is there any correlation to find overall heat transfer coefficient of superheater with respect to temperature? Or is there any constant reference...

29 April 2020 4,459 3 View

How can I find the vapour flow rate in an evaporator?

Hello everyone, I am dynamically modelling an evaporator. The evaporator works under constant pressure. I just know the inlet flow rate of the feed. Is there any way to obtain the vapour flow rate...

28 April 2020 9,016 0 View

Pressure control in a boiler?

hello, I have dynamically modelled a boiler in a closed system. so as its a closed system the pressure of the boiler rises with time. So I need to model a control valve to regulate the steam flow...

09 February 2020 5,542 0 View

How to know how much amount of electrical power is required to convert water into steam?

Can someone tell me how much amount of power is required to convert 100 liters of water into steam using electric boiler and how can i convert electrical power used by electric boiler into Q from...

23 January 2020 2,363 5 View

Is not GIS an important tool in spatial Epidemiology? Why not most researchers are not used it in their research?

What is problem preventing researchers to use GIS?

29 April 2019 5,911 13 View

How to generate generic fatigue load cases for chassis rear suspension if i have road load data for different tracks which represent the entire life ?

Currently i have road load data containing wheel transducer forces FX,Fy,FZ,MX,MY,MZ and strain gauge data at critical stress concentration zones. i want to develop generic load cases at wheel...

28 September 2016 6,317 2 View

How to find material properties( elastic modulus,poissons ratio,tensile strength)of a material which is a automobile part (knuckle) by nondestructing?

I have to find what is the the material properties of a part like knuckle which I have only one sample and it should not be destroy and find its properties.

04 November 2014 759 18 View

How can I apply shear stress in Ansys in 2d planar analysis?

I'm trying to undertake a 2D patch test for shear (Txy), but I cannot figure out how to apply a shear stress in ANSYS. I am presuming it has to do with applying a pressure, but it will only apply...

01 June 2014 904 6 View

Mathematical Modlling of a screw Compressor

I am trying to model a screw compressor in matlab/simulink. the parameters which i know are just input temperature, pressure and mass flow rate. I need to model a compressor with a desired output...

01 January 1970 4,628 3 View

Thermodynamic and transport properties of methanol?

Is there correlation to find out the thermodynamic and transport properties of methanol, such as density, thermal conductivity, specific heat capacity and others with respect to temperature as...

01 January 1970 8,916 4 View

Can formaldehyd-fixed gelatin be melt?

I am puzzled about the properties of gelatin, when used for tissue-embedding. Hard gelatin can be melt again by temperatures about 40°C. Formalin-fixed gelatin is like crosslinked protein and...

07 August 2024 1,686 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Microtome tissue sectioning - How to prevent chatter of paraffin tissue specimen sections?

Hello everyone, I have recently started using the microtome device for sectioning of paraffin-embedded mice lung. While I had some success in sectioning and observing proper ribbons, some of my...

06 August 2024 666 4 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

For the moringa oleifera extract using ethanol as the solvent,what is the alternative method to concentrate the extract other than rotary evaporation?

99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified

31 July 2024 5,113 4 View

HAs anyone used TGA to find activation enegy of water evaporation?

I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....

28 July 2024 9,545 6 View

Do we put respondents data in research methods or findings section of a qualitative study?

Are both ways acceptable, or is there any convention to them? Thanks.

22 July 2024 6,988 4 View

Radar Detection Probabilities using beta distributed Scattering Cross section?

Currently I need to calculate detection probabilities (PD) from radar cross section (RCS) data. Beta distribution parameters for this RCS data are calculated and will be used in Swerling0...

22 July 2024 868 0 View

Systematic review meta-analysis paper?

Hi everybody, We are trying to write a systematic review meta-analysis paper. But I could find 19 references. I think 19 references are not enough to do a meta-analysis section and it is better to...

10 July 2024 5,490 5 View