Overall heat transfer coefficient of superheater?

Hello, I am modelling a superheater in simulink. Is there any correlation to find overall heat transfer coefficient of superheater with respect to temperature? Or is there any constant reference...

29 April 2020 4,259 3 View

Is not GIS an important tool in spatial Epidemiology? Why not most researchers are not used it in their research?

What is problem preventing researchers to use GIS?

29 April 2019 5,749 13 View

How to generate generic fatigue load cases for chassis rear suspension if i have road load data for different tracks which represent the entire life ?

Currently i have road load data containing wheel transducer forces FX,Fy,FZ,MX,MY,MZ and strain gauge data at critical stress concentration zones. i want to develop generic load cases at wheel...

28 September 2016 6,118 2 View

How to find material properties( elastic modulus,poissons ratio,tensile strength)of a material which is a automobile part (knuckle) by nondestructing?

04 November 2014 571 18 View

How can I apply shear stress in Ansys in 2d planar analysis?

I'm trying to undertake a 2D patch test for shear (Txy), but I cannot figure out how to apply a shear stress in ANSYS. I am presuming it has to do with applying a pressure, but it will only apply...

01 June 2014 666 6 View

Mathematical Modlling of a screw Compressor

I am trying to model a screw compressor in matlab/simulink. the parameters which i know are just input temperature, pressure and mass flow rate. I need to model a compressor with a desired output...

01 January 1970 4,488 3 View

Thermodynamic and transport properties of methanol?

Is there correlation to find out the thermodynamic and transport properties of methanol, such as density, thermal conductivity, specific heat capacity and others with respect to temperature as...

01 January 1970 8,818 4 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View

I have designed reflectarray element and feeding it though Horn Antenna on HFSS. After full wave simulation, I am not getting desired results?

I have designed reflectarray element to generate OAM beams at 5.8GHz and feeding it though Horn Antenna on HFSS. After full wave simulation, i am not getting desired results i.e Radiation pattern...

01 March 2021 9,701 5 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to remove fatty material from plant extract?

The resultant solid was partitioned three times with 250 ml of petroleum ether (40-60/c) to remove any fatty material and evaporated to dryness.

28 February 2021 9,464 2 View