Overall heat transfer coefficient of superheater?

Hello, I am modelling a superheater in simulink. Is there any correlation to find overall heat transfer coefficient of superheater with respect to temperature? Or is there any constant reference...

29 April 2020 4,259 3 View

Is not GIS an important tool in spatial Epidemiology? Why not most researchers are not used it in their research?

What is problem preventing researchers to use GIS?

29 April 2019 5,749 13 View

How to generate generic fatigue load cases for chassis rear suspension if i have road load data for different tracks which represent the entire life ?

Currently i have road load data containing wheel transducer forces FX,Fy,FZ,MX,MY,MZ and strain gauge data at critical stress concentration zones. i want to develop generic load cases at wheel...

28 September 2016 6,118 2 View

How to find material properties( elastic modulus,poissons ratio,tensile strength)of a material which is a automobile part (knuckle) by nondestructing?

04 November 2014 571 18 View

How can I apply shear stress in Ansys in 2d planar analysis?

I'm trying to undertake a 2D patch test for shear (Txy), but I cannot figure out how to apply a shear stress in ANSYS. I am presuming it has to do with applying a pressure, but it will only apply...

01 June 2014 666 6 View

Mathematical Modlling of a screw Compressor

I am trying to model a screw compressor in matlab/simulink. the parameters which i know are just input temperature, pressure and mass flow rate. I need to model a compressor with a desired output...

01 January 1970 4,488 3 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

What is the indication of the absence of peaks in Methanol electrooxidation CV curves ?

I have several question regarding the MOR; hope anyone help me better understand. 1- in CV using (KOH+MEOH) what is the indication of absence of the redox peaks? shouldn't they exist as a sign...

28 February 2021 4,851 8 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Exit velocity of natural gas from pressurized tank?

Hi Guys. I'm a mechanical engineer and have a bit trouble, would be very glad if you could help me with my questions. I have a pressurized tank which contains Natural Gas at 200 Bar and 293...

26 February 2021 6,253 3 View

Anyone that can help with Maxquant TMT16plex which is missing?

Hi I am very new to proteomics analysis. I have got raw files from core facility running thermofisher TMT 16plex 4 hours. I cannot find on maxquant the option TMT16Plex there is only up to 11...

25 February 2021 1,675 3 View