How can I save the measurements made using ImageJ on a Stack of Images (I mean, to actually see those measurements in the saved pictures)?

Hi everyone, I'm currently checking some cuts of welded plastics parts and I come across with ImageJ. I'm really new using it. If I save the image (or the stack of images) the measurements does...

03 April 2016 408 2 View

How can I apply loads on elements as Temperature Dependent in ANSYS APDL?

09 October 2014 6,854 3 View

Variable Output -Element dependant Time HistPostProccess (APDL)

Hi everyone,I have the results for my ANSYS model, but now I was thinking to measure some things using "Time-History Post Processor Calculator". But I need to do it for a bunch of elements, and...

09 October 2014 3,431 1 View

It is possible to apply Symmetry Region on a rotating model on ANSYS WB? How?

08 September 2014 6,460 2 View

How can I add viscoelastic properties on ANSYS?

Hi everyone. I am doing some research about PEEK polymer and I need to add some values in ANSYS to make an analysis about viscous heating. I have the G'(w) and G''(w) from a DMA testing paper that...

07 August 2014 3,565 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to address this issue in the analysis of Real-Time PCR results?

To dear Researchers, I was analyzing a series of concentration for estimation of Real-Time PCR efficiency. The concentration was 1:10. I used MS-excel to evaluate Slope. The result of slope was -8...

01 March 2021 8,683 4 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Can I download BibExcel for MacOs?

Hi everyone, I would like to ask how I can download BibExcel software for MacOs? There are some links which are supported by Windows but I could not find it for Mac. or is there any other software...

01 March 2021 652 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View