How can I do cyclic pressure/compression application on the pressure sensor fabric by Instron tensile tester (3360 model)? How can I apply force on fabric by adjusting force as kPa unit?
How can I get time versus resistance change results with digital bench multimeter connected with computer?
11 January 2023 9,384 4 View
Is there anyone using an electrochemical working station CHI660E for characterisation of electromechanical performance of piezoresistive pressure sensor? Could you suggest source, references or...
06 January 2023 1,960 4 View
As far as I know, there are at least two docking tools that can be used for protein docking studies, namely the HDOCK server and the ClusPro server. However, I don't know how to validate the...
11 October 2021 2,733 5 View
I want to know how to produce cytokines in PBMC after being stimulated by allergens / antigens (e.g. house dust mites). Are stimulation by allergens 'alone' sufficient, or does it require...
20 June 2020 6,281 12 View
In literature, there are a lot of research about using chemicals containing long chain alkyl groups to prepare water repellenct substrate. However I heard chemicals containing these groups were...
09 March 2015 1,176 9 View
I would like to ask a question about using of linear motor E1100. I downloaded linear motor software to computer. It is working. I can work command table mode, triggered command table and...
01 January 1970 2,873 1 View
Hello everyone. I produced textile based piezoelectric pressure sensor. I got 8 V max. DC output voltage under impact by oscilloscope. I build rectifier circuit. But i can not succeed the...
01 January 1970 6,253 5 View
I did in silico study (molecular docking) of anti-malarial compounds' candidates that target the falciparin-2 and plasmodium falciparum dihydrofolate reductase-thymidylate synthase proteins and...
01 January 1970 970 5 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,538 4 View
need of sensor details or sensor development for this question.
28 July 2024 4,539 3 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
I try to understand the ESP mechanism working. What kind of sensors it has, Is it necessary to modify or boost its mechanical ?
15 July 2024 4,772 1 View
I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...
13 July 2024 3,631 4 View
Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...
11 July 2024 5,380 0 View