How can I develop a rotating reactor with solid-gas feed injection?

More Gajendra Kumar Gaurav's questions See All

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

I am carrying out an experiment on Trichoderma. How can I measure OD of the fungal growth after 7 days?

I am carrying out an experiment on Trichoderma and need to measure OD of the fungal growth after 7 days. Unlike bacteria, fungus clump together making It difficult to get OD for the fungal growth....

11 July 2024 6,251 1 View

What is the standard way of deposition of MoO3 and Ag by thermal evaporation?

Dear friends, I am trying to develop an efficient n-i-p structure device (perovskite, colloidal quantum dots, organic solar cell). Many researchers widely use MoO3 and Ag as metal electrodes in...

05 May 2024 8,814 4 View

I am trying to deposit nanofibers on FTO glass substrate, Is it possible to place FTO on rotating drum which have negative potential ?

The FTO is deposited on glass substrate

01 May 2024 9,262 1 View

Which growing medium is best for the Bacillus Globigii sporulation with maximum yield?

Please provide an answer along with the reference.

26 March 2024 7,488 2 View

If a same glassware is used more than once in a measurement, how to consider or calculate total measurement uncertainty ?

Suppose I am making a solution of a particular concentration and I am doing it with step wise dilution from a stock solution. If I use a same volumetric flask for 2 time for the consecutive...

14 January 2024 1,976 10 View

Can anyone suggest in scenario reduction techniques for solving multi stage stochastic problem ?

In scenario based approach, for reducing computation burden and complexity, scenario reduction technique is essential. I want to develop new scenario reduction technique. can anyone suggest in...

22 December 2023 3,496 1 View

What is the difference between the Lienard based oscillators and Consensus based osillators?

The virtual oscillator based grid forming inverter topologies are broadly divided into two categories. First one is Lienard oscillators (Van der Pol, Dead-zone). The second one is Consensus based...

12 December 2023 9,817 0 View

Can a fto electrode be reused for second time? If yes how can we clean it before reusing it?

I've got a new fto electrode and did my testing with a copolymer material. Now I have another material ready so can i reuse the fto electrode for the second time. If yes how to clean and reuse it.

04 December 2023 5,964 1 View

What is the probable mode of action of Marma Therapy/massage? How it subsides pain?

Marma points are one of the fundamental concepts of Ayurveda. Detail about each and every marma is elaborated in the 6th Chapter of Sharir Sthana of Susuta Samhita. However, in this chapter, these...

17 November 2023 2,527 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

Why do we equate male and female arousal?

Women, on the other hand, can become physically aroused (increased blood flow in the reproductive organs) without becoming psychologically aroused even in the slightest. (Robert Weiss)

05 August 2024 9,537 2 View

How to start a Molecular Dynamics Simulation?

Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...

03 August 2024 3,371 3 View

Which will be the best software for the Hydration shell analysis with molecular dynamics?

I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?

02 August 2024 3,143 4 View

How to make a Lateral flow control line more uniform?

We have a lateral flow test on Sartorius 140 NC. The conjugate is gold-monoclonal antibody. Using different control lines (GAM, protein A, protein G) we get a very strong leading edge with reduced...

31 July 2024 4,510 3 View

Suggestions for the Annexin V Positive Control ?

Hello everyone, I am currently using washed human platelets to stain Annexin V as a procoagulant marker. Additionally, I am staining with PerCP-CD61 to identify platelet cells. So far, I have...

29 July 2024 8,624 1 View

CAD File of human's & rat's respiratory airways ?

Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...

29 July 2024 1,092 2 View

How to restart MD without using checkpint file in GROMACS?

Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar

29 July 2024 3,084 8 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

Mohsen Karimi

Hi,

For the rotating part you can either choose Multiple Reference Frames (MRF) or the Sliding Mesh (SM) method and if the total volume of dolomite is less than 10% you can safely use DPM model to inject and track the solid particles.

If you can add more details about the problem, I might be able to help better.

Just sent you two tutorials about MRF and SM.

Can you please send me your address.

Sorry I meant your email add! so I can attach the tutorials.