How to find out or construct(?) the right priors from data of previous experiment to use in a bayesian glm?

I have the following equation, Eating choice (Yes/No)~ Box type (A/B/C). So the question is whether a certain box type affects eating choice in groups of dogs. The eating choice of each member in...

10 February 2021 6,024 9 View

What are the ways to test the knowledge level of agricultural labourer about their day to day work?

what kind of test can I do for testing the level of knowledge about their daily operation?

03 February 2021 7,583 10 View

Why the bandgap of CH3NH3PbCl3 films are different for spin-coating method and electrospinning method?

The observed bandgaps are 3.8 eV and 3.4 eV for spin-coated and electrospun films, respectively. What are the possible reasons?

08 January 2021 5,646 6 View

Why monoethanol amine is used as flocculant?

I want to know the reaction mechanism of monoethanol amine used as flocculating agent for rerefining used lubricating oil. Here I have attached one research paper where MEA (monoethanolamine) is...

01 January 2021 5,681 2 View

Problem with GST-fusion protein elution- Can anyone help?

18 December 2020 4,559 6 View

How can I determine metal concentration of Used lubricating oil by AAS?

I am a junior research fellow in the department of Chemical Engineering, Nit Durgapur. I want to know that how can I determine various metal such as Fe, Cr, Mg, Mn, Pb concentration present in...

15 December 2020 9,887 3 View

Regarding the O 1s XPS pf phyllosilciates, the peak near 531 belongs to Oxygen vacancy sites or O bonded to the Si from the silicate tetrahedra?

In O 1s spectra, usually the peak near 531 eV belongs to oxygen vacancy sites in oxides, however, in silicates, these peaks are often reported to originate from O-Si. I am confused if the intense...

10 December 2020 9,496 2 View

What is the mol. weight of GFP-11 tag?

Hi, I am trying to find out the mol. weight of GFP 11 because it is tagged to my protein of interest which is 17kDa. GFP 11 has been tagged with my protein of interest while GFP 1-10 is tagged...

09 December 2020 1,863 1 View

How to PEGylate Fluorescntl Polystyrene Particle?

I have Fluorescent Polystyrene beads. I need to graft PEG on the surface of it. I am looking for a protocol to do that. Also need to know which experiment to perform to be sure about the grating.

01 December 2020 7,860 1 View

How to control for categorical independent variables (e.g., education) when doing regression discontinuity using STATA?

I am conducting a regression discontinuity design where the dependent variable is continuous while control variables are categorical (except the treatment variable). In the usual regression...

01 December 2020 583 3 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

High aspect ratio hexahedral mesh optimization solver?

I am interested in evaluating mesh optimization solvers that converge to high aspect ratio unstructured hexahedral grids. In other words, I am interested in a solver that optimizes warpage,...

26 February 2021 7,279 2 View