I want to model friction damper..but it has deformation limit(slip has limitation). I want to define the elasticPP material or Steel Material with a limit to deformation.
Someone advise me to use 1 to 2mm undersized pellet but it is not available. Do anyone have any experience in the field of tunnel kiln ?
28 June 2024 6,355 0 View
For fatty acid and amino acid profile analysis in Litopenaeus vannamei post-larvae (1-1.5 gr), is it necessary to remove the head and peel? or it's possible to use whole body including head, peel...
04 June 2024 4,497 0 View
I am currently working on a drug-loading process that should be examined by UV detection. One of the processes I have to apply to detect the therapeutic agent concentration is utilizing Cerium...
25 May 2024 9,896 0 View
Can someone help me with fit and simulation in nova app? I can't get a good fit for my data
19 May 2024 5,086 2 View
If we want to obtain Aerogel from Hydrogel for Oleogel development, does the syneresis of Hydrogel affect the future oil absorption process in Aerogel? Does the volume reduction due to syneresis...
17 May 2024 9,141 1 View
I have FeCl2 crystals and I want to produce FeSO4.7H2O based on the reaction below: FeCl2 + H2SO4 = FeSO4 + HCl I dissolved the FeCl2 crystal in water, added equivalent amount of H2SO4 to react...
21 March 2024 1,150 0 View
I've been working on SCF calculations using VASP, and I've noticed that even with the following INCAR settings, I'm not seeing eigenvalues close to 1 or 0 corresponding to electronic states. Does...
10 March 2024 3,945 2 View
When we want to prepare a Gel from two gelling agents, is it better to prepare their hydrogel separately and then mix them? or is it better to mix their dry powder and then prepare hydrogel? which...
21 January 2024 1,949 2 View
Hello everyone I recently emailed the editor in chief of a journal about our manuscript submitted more than a year ago. Although 6 months ago, one of the journal's staff replied that it is "under...
11 January 2024 4,406 11 View
I have data of G', G'', and Angular Frequency and I want to know how can I Calculate Phase Angle based on them?
05 January 2024 5,157 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
Hello, dear colleagues, I would like your help in finding a reference that provides an average water savings due to plastic recycling compared to the consumption of virgin materials, preferably...
29 July 2024 4,630 0 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?
25 July 2024 9,408 0 View
I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...
24 July 2024 4,393 2 View
Hello everyone, I am currently pursuing a PhD in Environmental Engineering with a focus on microplastic studies. My background is in Civil Engineering, and I am relatively new to working with...
18 July 2024 7,258 3 View
I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...
16 July 2024 5,047 0 View