How can I add confidence interval in time series in R?

More Shihab A. Shahriar's questions See All

Comment ajouter une recherche ?

En suivant toutes les étapes mentionnées sur (ajouter une recherche) il me signale erreur, ressayer, j'ai essayé plusieurs fois, sans succès, toujours il me signal erreur, ressayer

02 August 2024 9,719 1 View

How can I handle unavailable papers in a systematic literature review?

Context: I am writing a Systematic Literature Review (SLR) as part of my master's thesis project. After initially screening the titles and abstracts of 338 papers from four selected databases, I...

29 July 2024 9,370 4 View

Why practical assessments of dislocation density by XRD ignores the texture which apparently affects the result?

As one can read in numerous papers on this matter, the dislocation density is derived from the dependence of peak broadening on the diffraction angle, that is, on considered reflections. Thus, to...

28 July 2024 6,496 5 View

Is there any other efficient technique, as an alternative to multiple linear regression ?

with secondary data collected from central bank to know the impact of digitalization in banks profitability, how can its impact be more precisely measured through econometric tools.

21 July 2024 7,295 10 View

Hellow every one i have a question, please help me. How ESP car working?

I try to understand the ESP mechanism working. What kind of sensors it has, Is it necessary to modify or boost its mechanical ?

15 July 2024 4,772 1 View

Are diatom inclusions found in shellfish shells?

Mangroves were reported to eat into limestone atolls like so much cake - but could it have been diatom partnerships at mangrove roots that ate into the rock? If gypsum formation is a clue, how...

12 July 2024 159 2 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

Is there any guidelines about zooming out a chromatogram?

Hi, Just curious to know that in chromatography, a chromatogram should be zoomed to what scale? 10 times of output , 50X or ..? Is there any regulation or general chapter which describes this?...

03 July 2024 3,119 6 View

How to see whether my protein is aggregated using western blotting?

I am working on one protein which gets aggregated (similar to alpha-synuclein and tau) in certain neurodegenerative diseases. I am trying to confirm the aggregation using Western blotting....

30 June 2024 5,060 3 View

Do body proportions of sharks change after drying?

Dear colleagues, I would be grateful to anyone who can answer my two questions: 1. Do the proportions of the shark's body change after drying? In other words, is it possible to discriminate two...

30 June 2024 6,101 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How is energy cycled through the Earth's climate system and how do matter cycle and energy flow through the rock cycle?

08 August 2024 8,162 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there any instruments for studying time similar to the way it is in space?

There are a huge number of methods for studying objects in space, according to the senses (and not only). Mechanical, thermal, optical, acoustic, electrical, magnetic, based on particle beams,...

06 August 2024 7,102 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Why does the MFDFA algorithm need to calculate the profile of the time series?

As described in the Multifractal detrended fluctuation analysis (MFDFA) algorithm, it at first calculates the profile of the time series, and then other steps are operated on the profile....

05 August 2024 9,366 2 View

Abhijit Mitra

Time Series Forecasting - r-statistics.co

r-statistics.co/Time-Series-Forecasting-With-R.html --u can see this site

Saadoun Salimi

https://stackoverflow.com/questions/31951495/plot-time-series-with-confidence-intervals-in-r

https://cran.r-project.org/web/packages/ggfortify/vignettes/plot_ts.html

https://rcompanion.org/handbook/C_03.html

https://www.youtube.com/watch?v=HkZSmviB8ps

https://www.youtube.com/watch?v=x4ekQ1nanQ4

https://www.youtube.com/watch?v=cNJQ8bEzL3M

Ram kumar Singh

Hi Shihab A. Shahriar ,

Below is the example of Rscript for ARIMA confinence interval-

#tsdata is data to be used for arima model

fitARIMA