10 October 2017 3 869 Report

Actually i am new to COMSOL so don't know much about it. I want to analyze the heat and mass transfer simultaneously so kindly tell me how to proceed. It will be a great help.

More Anas Imdad's questions See All
Why does the yield stress increase with dislocation density? Even though without any dislocations, the strength would be even higher?

I cannot understand that increasing dislocation density increases the yield strength of material but how?

11 December 2018 1,886 5 View

I am working on membrane distillation model (DCMD) in COMSOL.My Velocity profile is correct but my temperature profile is defective?

My velocity profile is just coming according to the concerned research paper but my temperature profile is not coming according to it and is not changing in the region. The temperature value is...

11 December 2017 1,542 4 View

I have a problem in MATLAB program.I have made a program for Direct Contact Membrane Desalination (DCMD). The answers are deviating a little bit?

I have attached my Matlab code and the reference paper through which i got the idea of making the code (Page # 6).My temperature values are deviating upto values of 10. Kindly tell me what is the...

10 November 2017 9,468 0 View

Is it necessary that amplitude of Forced damped vibrations come to zero after some time. I have made a simulink program for vibrations of washing mch?

I have attached my simulink/Matlab model. Kindly tell me if there is any thing wrong with it?It is modeled on the basis of forced damped vibrations. The amplitude of model does not come to zero...

10 November 2017 6,607 4 View

Which physics modules to be used in the membrane desalination/distillation in COMSOL?

I want to perform simulation in COMSOL so trying to search for the module which is to be used to achieve this goal.

09 October 2017 5,943 0 View

Is there any material that has high specific heat as well as high thermal conductivity?

We are trying to integrate such material in membrane desalination project.

09 October 2017 1,890 3 View

Hello Everyone. I am doing membrane desalination project and i want to draw the porous membrane. Which software should i use?

Actually i want to do FEM analysis so i want to make porous membrane in software

09 October 2017 7,627 6 View

Similar questions and discussions
Problems about acousto-optic coupling in Comsol, how to check whether the moving mesh is correct?

I’m trying to reproduce the acousto-optic coupling simulation in the paper Frequency–angular resolving LiDAR using chip-scale acousto-optic beam steering. LNOI(lithium niobate on insulator) is...

13 August 2024 9,795 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close