How to calculate the score of SF-12V2?

SF-12v2 is the latest method to study health, but its calculation method is difficult to obtain. I wonder if you can provide the calculation method of SF-12v2. Thank you very much.

17 June 2019 6,108 2 View

How to understand open-set conditions for object detection models?

1. As I learned from related papers, open-set conditions refers to new objects encountered that were not seen during training. for object classification, open-set conditions can be cat images for...

12 August 2018 4,793 2 View

What is the best method of extracting Astaxanthin from shrimp and crab waste?

I would like to know the best solvent extraction procedure of Astaxanthin from shrimp and crab waste.

21 January 2018 4,020 3 View

What is the performance of flat (0 angle) Solar PV installations?

What is the performance of flat (0 angle) Solar PV installations?

10 December 2017 5,648 21 View

No title

I am doing the experiment for testing the percentage of immune cells in the peritoneal fluid cells(mouse), i repeated the experiment but each group of data from different mouse were different (the...

25 September 2017 158 3 View

Does anyone know how to do the FACS compensation for surface antigen and pHrodo E.coli bioparticle?

I isolate the monocytes from the peripheral blood and then I want to analyze the different phagocytosis ability in the subpopulations of monocytes by using surface antigen stain and pHrodo E.coli...

23 December 2015 3,675 1 View

Any isolation method for higher yield STIV(archeal virus) genome for topological studies?

I've been trying to isolate the genome of STIV ( double stranded Circular form ~18kbp) to study the topology. I've tried using proteinase K with Tris, EDTA, SDS digest at 37 degrees Celsius...

13 September 2015 661 2 View

What is the thermodynamic parameters of RNA mismatched base pairs?

18 November 2014 9,720 3 View

Can anyone assist me with native gel troubleshooting?

I have question regarding Native gel (15%). My protein molecular weight is 13 kda and it supposed to form dimer when ligand is added.The ligand is around 500Da. When I run native gel, my protein...

29 August 2014 9,029 6 View

How do I check oligomers / dimers of the protein using Native Gel ?

I am new to protein chemistry, Can I know how do I check oligomers / dimers of the protein using Native Gel ? Thanks in advance.

27 August 2014 1,384 6 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Logistical regression using SPSS for a dichotomous dependent variable, with an independent variable of 1, 2, 5 and 10 seconds?

I have an experiment with 28 participants The independent variable is the times 1, 2, 5, and 10 used as the cross hairs during a task These 4 times were tested using 4 different blocks, each...

03 March 2021 9,692 2 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View