Explain material modeling of Polymer Composites in ANSYS?

More Shivanand N Pujar's questions See All

How Can I Move further once I Identify DEGs through RNA-seq For Fe and Zn in grains?

After finding Differentially expressed genes in low and high Fe inbreds lines, how should i exploit those results further. Thank you.

06 June 2021 4,605 1 View

Does RASPA molecular simulation package take .xyz files for a crystal structure? or it reads only .cif files?

I'm a very much beginner in using RASPA. I want to simulate a crystal phase, for which I have .xyz file. Can RASPA read .xyz files?

29 May 2019 8,409 1 View

How to find Weight fractions of mixed phases (two phase) from the XRD data?

We have synthesized NaYF4:Yb, Er UCNPs and annealed for different temperatures in the range of 200 to 600°C . In the XRD we observed phase transformation from Cubic to Hexagonal, for the higher...

26 February 2019 3,834 3 View

Can anybody tell me the relevant references for design of buttress retaining wall?

Can anybody tell me the relevant references (book, Journal) for design of buttress retaining wall? Please tell if any

25 March 2018 6,860 1 View

How can we calculate the transmission error for a hypoid gearset?

I have learnt that transmission error is the result of various factors like varying mesh stiffness, tooth bending, tooth macro and micro geometries etc. However, various software predict the...

20 February 2018 2,121 0 View

Do we have more Chromosome doubling chemicals?

Since I am working on production of double haploid lines in Onion which requires colchicine as a chromosome doubling chemical, hence please suggest me some more chemicals of similar property as...

24 July 2016 9,079 3 View

How to calculate percentage load carried by piles and raft through PLAXIS 2D software?

I have plotted the axial pile load versus pile length for piled raft by PLAXIS 2D software. Load - UDL - 200 kPa Domain -200*80 Clay soil Cu = 80 kN/m^2 Es = 20 MPa Epile , Eraft = 20...

10 April 2016 957 6 View

Join to Mechanical Engineers

I want to join this team

06 April 2011 3,101 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Manish Kumar Dubey

You can add Elastic properties in ANSYS: Material model section

Orthotropic or Anisotropic depending on the fiber orientation of the composite.

This link on

DROP ANALYSIS OF BLOCK IN EXPLICIT DYNAMICS ANSYS

https://www.youtube.com/watch?v=xPDDd9925jo

Md. Washim Akram

https://www.sciencedirect.com/search?qs=material%20modeling%20of%20Polymer%20Composites%20in%20ANSYS&show=25&sortBy=relevance