I want to know the possibility of P3HT solution degration with time.
P3HT does not undergo noticeable degradation by 1,2-DCB, however, other factors (air, light, contaminants) may negatively influence the stability of the solution.
Agree with Tomasz but practically devices do not perform well if P3HT is dissolved too earlier before the fabrication.
.Thanks for the comments
Sb2S3 has a bandgap of 1.7 eV. thin film of Sb2S3 shows high absorbance in the visible range, why it is so? why dont we get a high absorbance at a wavelength corresponding to the band gap energy...
07 August 2016 8,505 0 View
I carried out I(V) characterization of my device, In dark the device showed diode like behavior while in light curve shifted to the first quadrant , what would be the reason for this? normally in...
11 December 2015 4,770 5 View
I want to protect a part of FTO for the cathode connection. I usually use spin coater to deposit thin films. To save some region of FTO for the connection , I used Teflon tape but it did not work...
31 December 2014 9,114 5 View
I would like to calculate the cds band gap using UV-Vis absorption.
31 December 2014 2,295 5 View
I want to etch my FTO substrate to fabricate multiple photovoltaic cell on single substrate. I want to know the best possible procedure for the controlled etching of FTO.
31 December 2014 5,276 4 View
The off-stoichiometric Ni-Mn-In heusler alloy undergo martensitic transition under the influence of varying temperature or magnetic field. I am having problem to identify the low temperature...
31 December 2014 2,942 6 View
I have fabricated a Solar cell which has diode like behavior in dark, but has linear I-V curve in 1 sun illumination. What could be the reason of this linear IV curve under light?
31 December 2014 7,498 12 View
I want to deposit thin film of P3HT using spin coating method. My first question is for how long should we stirrer P3HT solution in dichlorobenze? Secondly I need to know how many times should I...
11 December 2014 3,496 5 View
Approximate concentrations are require in compared with the WHO permissible limts
11 August 2024 2,723 1 View
Hey there, As a synthetic chemist delving into theoretical calculations for my imidazolium-based organic molecules, I would greatly appreciate any guidance on the appropriate input instructions...
09 August 2024 5,444 7 View
I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...
08 August 2024 8,329 0 View
Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.
07 August 2024 8,782 3 View
Greetings When one is to perform Simulation or modelling of Pyrolysis of Biomass Waste materials using Aspen Plus software, and one has both the macromolecules breakdown (Cellulose, Lignin and...
06 August 2024 5,023 1 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
What is the method for analytically calculating the wear and service life of polymer-polymer sliding pairs?
04 August 2024 1,078 1 View
What is the most suitable experimental setting to understand the consequences of a particular gene: (1) targeted degradation of the specific transcription factor (TF) of the gene, followed by...
04 August 2024 6,265 1 View
I used humic acid at 0.044 g/kg soil in my pot experiment. But finally, I have to recommend kg/ha. Each pot's soil weight was 11 kg. What is the solution?
02 August 2024 7,186 6 View