Does applying the rule of thumb perform better in pest and disease early warning systems or statistical models?

03 March 2014 0 2K Report

Rule of thumb proves better for most instances and the predictions of statistical models are close to the real situation. Which one should be relied on the most?

Badges
Science method

More Ap Ramaraj's questions See All

In 80% AWHC, how to maintain the moisture level. for example today is 80% after 2 days its go around 60% means how to maintain at 80%

In pot experiment with clay loam soil moisture stress condition

01 February 2017 5,286 0 View

How can we maintained the moisture stress in pot experiment wit 80%, 60% and 40% AWHC (Available water holding capacity) ?

I am going to conduct pot experiment in elevated temperature condition

11 December 2016 7,604 6 View

How does one draw an uncertainty graph as given in IPCC?

I have tried in Excel and searched in MatLab and couldn't find any suitable graph to show projections from %GCM I studied. Is there any tool to do this?

11 December 2013 2,787 4 View

How does one do a Monte Carlo simulation for climate projections using MatLab?

Can someone help me out in running a Monte Carlo simulation using MaTLab? Is there any simple step-by-step procedure available?

11 December 2013 3,104 2 View

Which method is best to do uncertainty analysis?

I have projections from 20 GCMs for my location. Is it Monte carlo simulation or Bayesian?How to do that in MAtLab? Any readymade scripts available?

11 December 2013 3,906 11 View

What is the best programming language to analyse data in Excel or ASCII?

Need to analyse huge data as I am a meteorologist working on uncertainty in climate models.

03 April 2013 7,902 17 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Are there any good simple systems or platforms to recommend?

In order to show people the beauty of control and enhance enthusiasm for learning control theories, are there any good simple systems or platforms to recommend?

05 August 2024 10,034 1 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View