Does anyone know of any articles or resources which explain INLA and R-INLA?

More Pau Aragó's questions See All

Can plants’ cuticles/stomatas absorb small peptides? What is the maximum size amino acids/peptides they can absorb?

I understand that amino acid absorption can be due to passive diffusion as well as active transport, and both depend on the architecture of the leaf, age of the plant, climatic conditions (mainly...

01 May 2023 3,081 0 View

What is the difference between fish emulsion and any other amino acid fertiliser for soil or plant growth?

Amino acid fertilisers are a real alternative to chemical NPK fertilisers. They can stimulate soil and leaf microbial population; hence they help increasing organic matter and soil aeration, they...

10 April 2023 9,409 2 View

Is it right for me to use one way repeated analysis of variance (ANOVA), instead of multivariate analysis?

Hi, I have one independent variable, treatment groups, and one dependent variable, platelet count measured in different time points (4 time points), in vivo rats. There is same no. of rats per...

01 December 2022 4,716 2 View

How to over come error in SAP2000 analysis?: Error in seismic x?

Hi everyone I have a 3-level structure, it tells me that I have an error in the LOAD CASE with an earthquake in the X direction, but I defined it as an acceleration. What would be the error...

31 August 2022 2,098 0 View

How can I retrieve the main transcript from snpEff?

Hi, in those cases that snpEff returns different annotations, for...

07 July 2022 2,074 0 View

Are there published normality values for qEEG?

We need normality values to do qEEG in our laboratory . We need values of absolute power, relative power, average frequency and coherence, by age. We were working with a Neuronic device that...

30 September 2020 5,104 1 View

Why is my pushover analysis (SAP2000) taking so many null steps?

Hi experts, I am developing a pushover analysis of a structure with SAP2000. It is a reinforced concrete structure that I want to compare with the same structure, but adding a shearwall. The...

28 January 2020 751 5 View

Retinol as water in oil in water emulsifier?

Hi Folks, Have you ever used retinol to emulsify water inside the oil phase of a w/o/w emulsion? Retinol shouldn't be a good emulsifier as it is very hydrophobic, but it seems that the hydroxil...

14 January 2020 8,182 3 View

I have too much experimental variability in OGD procedure. Any solutions/ideas?

Hi, We are working with an in vitro model of blood brain barrier (BBB) using bEND3 cells and oxygen/glucose deprivation procedure to study the BBB damage during a cerebral ischemia. We have...

27 November 2016 1,884 3 View

Does exists some repository with bam/fastq files?

Hi everybody I am trying to set up a pipeline for detecting large gene deletions. I think the samples that I am testing don't contain this kind of deletions. I would like to test the pipeline...

21 March 2016 5,237 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

If we are using snowball sampling technique, how do we justify the true representativeness of the sample statistically? is there any statistical test?

Are there any statistical methods to justify your sampling technique using SPSS or AMOS?

05 August 2024 9,153 4 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View