Anyone know how to do that in CFD-post.
Please answer asap.
Thanks.
how frictionless boundary condition is set up in fluent?
02 March 2019 4,002 3 View
In some book both words are use with si and ci engine. in some ci and sI engine both have knocking. what is actually difference between these two word??
31 December 2018 6,696 2 View
while setting up parameters in Fluent I have used like these: Used Boussinesq approximation and using nondimensionalized I put volume expansion coefficient as Ri/g(=10) so for Ri= -1 case I set my...
03 April 2016 3,976 1 View
what is mean by saddle points in vortex shedding and how can it be captured?
01 February 2016 5,353 4 View
Anyone who knows how fluent is calculating those parameters inside the software please reply.
31 December 2015 8,226 0 View
my question is is it my simulation is correct? flow is going from downwards to upwards and fluid temperature is high compare to cylinder.why is reversed flow occur?
11 December 2015 7,362 3 View
Strength is increased with carbon but i don't know whether the value of modulus of elasticity change or not?
11 December 2015 7,629 3 View
i am confused by below explanation: 1) According to Grashof number definition value of Gr is more in case of vertical pipe assuming other parameters are same so it shows that heat transfer is more...
11 December 2015 4,228 10 View
This question is asked because mode of heat transfer in radiator is forced convection so why it is called radiator? is there any way related to radiation?
10 November 2015 3,393 4 View
I
10 November 2015 4,094 0 View
Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...
07 August 2024 269 3 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...
06 August 2024 977 1 View
Hello! I am trying to calculate the sumatriptan molecule, but it has been counting for five days and it does not stop. It seems to me that it is too long and I am doing something wrong. Please...
25 July 2024 3,364 5 View
Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...
21 July 2024 1,680 2 View
Dear Researchers, My question is associated with the "MDCI" method in Orca. Please let me clarify my question using a simple example: Suppose we are going to perform CBS extrapolation using "!...
21 July 2024 1,632 0 View
I'm trying to study the effects of introducing vacancy defects in my material. If I optimize my structure and find the lattice parameter before introducing vacancy, should I again optimize my...
18 July 2024 1,794 2 View
I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...
16 July 2024 3,212 5 View
Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...
11 July 2024 5,380 0 View
Hello dear colleagues and professors Please what is the recommended type of pseudopotentials for QE? ultrasoft or norm conserving?? And from where get all types of pseudos (us, nc, pbe,...
09 July 2024 9,541 5 View