how frictionless boundary condition is set up in fluent?
Interested equstion.
In ANSYS Fluent you can define a wall boundary condition where you can switch from a no-slip wall to a specified shear stress wall. If you specify here zero shear, than it is a frictionless (free slip) wall.
Regards,
Dr. Th. Frank.
https://www.sciencedirect.com/search?qs=frictionless%20boundary%20condition&show=25&sortBy=relevance
In some book both words are use with si and ci engine. in some ci and sI engine both have knocking. what is actually difference between these two word??
31 December 2018 6,696 2 View
while setting up parameters in Fluent I have used like these: Used Boussinesq approximation and using nondimensionalized I put volume expansion coefficient as Ri/g(=10) so for Ri= -1 case I set my...
03 April 2016 3,976 1 View
Anyone know how to do that in CFD-post. Please answer asap. Thanks.
02 March 2016 366 0 View
what is mean by saddle points in vortex shedding and how can it be captured?
01 February 2016 5,353 4 View
Anyone who knows how fluent is calculating those parameters inside the software please reply.
31 December 2015 8,226 0 View
my question is is it my simulation is correct? flow is going from downwards to upwards and fluid temperature is high compare to cylinder.why is reversed flow occur?
11 December 2015 7,362 3 View
Strength is increased with carbon but i don't know whether the value of modulus of elasticity change or not?
11 December 2015 7,629 3 View
i am confused by below explanation: 1) According to Grashof number definition value of Gr is more in case of vertical pipe assuming other parameters are same so it shows that heat transfer is more...
11 December 2015 4,228 10 View
This question is asked because mode of heat transfer in radiator is forced convection so why it is called radiator? is there any way related to radiation?
10 November 2015 3,393 4 View
I
10 November 2015 4,094 0 View
What should be the equation for halfway bounce back boundary condition for flow field with forcing term?
08 August 2024 7,938 1 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View
I am using a windows system, what software I should use for hydration shell analysis with molecular dynamics?
02 August 2024 3,143 4 View
I am in search of a modified Hummer's method, which can be used to synthesis graphene oxide within 6-8 hours. As I am a student it is not allowed for us to work after 5 in the laboratory. So I am...
01 August 2024 8,368 2 View
I have an RNA-seq data that I have analysed using Limma-voom and have extracted the gene IDs, log2FC and the p-values. At p value < 0.05, I have over 10,000 DEGs, however, when I run the GO...
31 July 2024 225 2 View
Dear All, My lab primarily works on insect wing patterns. In one of the projects, my student and I have defined 19 abnormality characters on the forewing and 6 abnormality characters on the...
31 July 2024 6,464 5 View
Dear all, I am working on particle deposition in human's & rat's respiratory airways using CFD and I am looking for the 3D CAD file for my simulations (STEP or IGES format). If somone has such...
29 July 2024 1,092 2 View
Dear All Gromacs User I would like to restart MD without using checkpint .cpt files? I heard there is a way for acheiveing this. Any input and sugegstions are most welcome. Thanking You Budheswar
29 July 2024 3,084 8 View