Does anybody have idea about how to use INISTATE command in ANSYS APDL?

07 July 2015 0 3K Report

i am doing transient structural analysis in that i have to give a initial stress in every load step . Please tell me how can i give this stress by using INISTATE command with the help of IST file ?

Badges
Science topic

More Balaji Paikrao's questions See All

Does anyone have idea about how I can simulate moving heat source in ANSYS?

I am doing a welding simulation in ANSYS. For doing this I would like to know how can we simulate a moving heat source in ANSYS apdl.

04 May 2015 1,086 10 View

How do I find out residual stresses in welding using ANSYS?

how can we give a nodal teperature distribution as initial condition to the model so in a way to find a residual stresses in welding

03 April 2015 9,807 7 View

How can i get geometry format in NASTRAN format (.bdf) ?

i am doing welding simulation for that i have to import geometry file which should be in NASTRAN format (.bdf). Does anybody know how to create a geometry file in nastran format (by using any...

01 February 2015 4,152 1 View

Can anyone suggest how to write a subroutine in ABAQUS for welding analysis with Goldak heat source Model?

I have to use subroutine in ABAQUS for welding analysis with Goldak heat source Model. Does anyone have an idea how to write and link the subroutine in ABAQUS? I am a new user of ABAQUS. Thanks in...

31 December 2014 376 5 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View