How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

When is it unnecessary to change organisational culture?

As a former management practitioner, I recall a generally accepted view that changing organisational culture is difficult, so you should only attempt it if the organisational change that you are...

27 February 2021 2,595 8 View

Can I use a protein-devoid condition as my negative control in ELISA?

Hello, I am running a sandwich-type ELISA where I am trying to inhibit a protein-protein interaction using small molecules. For each experiment, I determine my Z' (Z-prime) to determine the...

23 February 2021 7,429 1 View

How to constrain genetic algorithm input u?

My real system (buck converter) can only take an input of 0 to 1 (duty ratio) and I need to constrain the system so the controller action keeps within this bounds. How can I do this? The code for...

22 February 2021 2,125 3 View

The Role of Town Planners in CAV Use?

Colleagues and I are about to begin a project investigating the role of town planners and local authorities in establishing the introduction of connected and autonomous vehicles (CAVs). What...

21 February 2021 2,247 3 View

Will SARS-CoV-2 Spike be broken into S1 and S2 by denaturing conditions?

Hello, I am performing a western blot of my SARS-CoV-2 Spike-pseudotyped lentiviral particles. I denature my virus by adding concentrated virus to 2X Laemmli buffer at 1:1, then boiling for...

17 February 2021 4,844 4 View

Why are the modelled and circuit system different in response for controlled buck converter?

[Images are attached at bottom] I am currently working on a buck converter controlled by two different control methods, Reinforcement learning applied to find PID values & a lead-lag...

16 February 2021 5,060 10 View

How can I interpret a ratio variable?

Dear colleagues, I am running a regression in which I have the following regression FoodExp = 67.04 DepRatio +.....e My interest is in the interpretation of the coefficient on the dependency...

16 February 2021 2,058 2 View

What is the best temperature to coat an ELISA plate?

Hello, I want to control the temperature of my ELISA plate during incubations to get consistent results. In general, what is the best temperature to coat the plate with antibody? I have been...

16 February 2021 2,377 7 View

SPSS - Merging files by ID numbers that contain letters?

Hi, I'm trying to merge files from a data base of 20 files, each containing about 4000 subjects. Unfortunately the ID numbers are actually a combination of numbers and letters (e.g., b1458219)....

15 February 2021 5,833 3 View

How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Energy minimization in LAMMPS using NVT ?

How do I do energy minimization in lammps with NVT ensemble ? I am using the following command and it does not seem to work. It stops at extremely high energy and gives me the error zero search...

01 March 2021 2,294 3 View

How can I edit suggested publications?

Hi there! I regularly receive suggestion about papers and authors that are totally out of my area. Does anybody know how I can fix this? Thank you!

01 March 2021 9,574 4 View

How to choose ANN number of hidden layers and nodes?

Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...

01 March 2021 6,200 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View