How to model contact condition between fluid and wall (VOF model, ANSYS Fluent)?

Hi, I am trying to simulate the mucus removal process using Fluent. I used multiphase model (air+mucus), simulation is working fine for the no-slip condition. In the realistic case, mucus will...

05 June 2019 3,725 1 View

Is it possible to give specified shear condition for the wall boundary in ANSYS Fluent?

Hi, Is it possible to give specified shear for the wall in Fluent. I have checked the manual and found that the wall can be modeled in the following ways (For VOF model, only adhesion contact...

05 June 2019 6,211 3 View

How to give user defined stress strain curve in abaqus?

Dear all, Any body know how to give stress strain curve with negative slope in abaqus

02 March 2019 1,630 4 View

How to calculate J integral using domain integral method?

Hi, How to calculate 3 components of j integral using domain integral method.

04 May 2017 2,912 2 View

How to calculate displacement gradient matrix?

Hi, Is it possible to calculate displacement gradient matrix from strain tensor and gauss point co- ordinates

03 April 2017 1,439 3 View

How to calculate the Orthocenter of triangle?

02 March 2017 1,495 3 View

Phantom node method in Abaqus XFEM implementation?

10 November 2016 9,912 0 View

GFEM and XFEM?

10 November 2016 9,705 1 View

Abaqus installation on client machine?

Hi, I am trying to install abaqus 6.14 (abaqus 2016) in my workstation (client machine) Error is coming while giving licence server, can anybody help me in resolving this error Error: Unable to...

08 September 2016 6,652 5 View

What factors need to be compared/ considered for validating numerical results with analytical results for crack propagation problem?

07 August 2016 6,089 4 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

How to use measure capacitance change in COMSOL time dependent study ?

I want to measure change of capacitance due to relative displacement between two parallel plates in COMSOL. Distance between two plates changes with time. So I'm using a time dependent study but...

26 February 2021 8,567 3 View

Error in comsol?

Dear respected researchers, while performing CFD analysis in Comsol it's showing like this Error: Nonlinear solver did not converge. The maximum number of Newton iterations reached can...

24 February 2021 249 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

How to Implement Elastoplasticity in a PCL model in COMSOL Multiphysics?

I am using COMSOL Multiphysics 5.5. I am trying to simulate the tensile test of PCL scaffolds. However, regardless of the strain, I have the elastic region all the time which is not true when it...

23 February 2021 4,050 1 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View