Is there sensor history output for energy ALLKE and ALLPD in abaqus 2020?

is there sensor history output for energy ALLKE and ALLPD in abaqus 2020? is there any one help me

19 November 2020 6,699 2 View

How can I invoking energy output in subroutine such sensor. the sensor can invoke output scalar such V. ?

07 November 2020 4,471 1 View

How can I invoking energy output in subroutine such sensor. the sensor can invoke output scalar such V. ?

07 November 2020 5,141 1 View

What kind of amides does the tendon consist of?

In visible reflectance spectroscopy performed on a bovine tendon, peaks were observed corresponding to tendon amides. But I do not know these peaks are related to what kind of amides.

16 August 2020 4,411 3 View

How to estimate Mean +SD for subgroups in a study in which results are presented for the main population?

Hello, I started working on collecting data for meta-analysis and I faced two-phase study, which in the first experiment the pharmacokinetic profile of 15 patients after drug administration were...

04 April 2020 9,678 3 View

What is my fault for getiing Push over curve for analyzing shear wall with connection ( Link element) on SAP2000?

Hi everyone. I modeled a shear wall with link elements as connections on SAP2000 but I have a problem with getting the correct push over curve for that ( I can't get the target displacement...

28 January 2020 8,261 3 View

How to calculate the life of a pixel if we know the useful life of LED?

For example, if the resolution of one LED is 2073600 pixels per image and the LED has 5 years useful life, how is the average life of each pixel calculated?

10 November 2019 9,565 2 View

What technologies can we expect to see have the biggest impact on maritime in 2030?

I think the autonomous systems, artificial intelligence, virtual reality, big data, cybersecurity and evolution of marine automation will probably be the next year's issues. What do you think?

10 April 2019 7,135 10 View

Mechanical Behavior and motion simulation in ansys maxwell ?

Hi. I want to simulate a motion in Ansys Maxwell, meaning that I want to simulate 2 magnets, one fixed in its place and the other can rotate around its center point ans as you know, the free...

14 January 2019 208 3 View

Which internal standard is suitable for running an organic reaction whose conversion will be analyzed by HPLC?

I want to run an organic reaction and determine its conversion by using HPLC since I am using water as solvent and cannot use GC for conversion determination. Since HPLC cannot detect typical...

01 January 2019 6,428 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

I need to accelerate corrosion in steel parts that are used in a salt-water environment. Is there a technique for doing so?

I have a structure that employs d-ring swiveling tie-downs that corrode during use and become "frozen". I have sample swivel assemblies that I wish to corrode to see if I can free them using one...

01 March 2021 3,739 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View