Current density in cathodic electrodeposition?

15 August 2022 1 6K Report

How can I determine appropriate current density value theoretically for cathodic electrodeposition process?

For this calculation, the parameters of the amount of electrical deposition, the amount of applied current or voltage, and the conditions of the aqueous solution are needed.

[email protected]

More Saeideh Ghaffari's questions See All

I observed this clumps in my MCF-7 cell culture. Does anyone know if it is normal or contamination?

29 April 2024 9,647 3 View

Mathematical relation for calculating the fluorescence enhancement constant?

I encountered the fluorescence enhancement in the DNA interaction process. Since the classical Stern-Volmer equation is used for the fluorescence quenching process, this equation cannot be used to...

16 February 2024 2,776 1 View

Is there anyone who has experience working with Hypoxic Chamber (Glove Box-COy)?

I want to culture Huvecs cells under hypoxic condition (hypoxic chamber), Does anyone know the cell culture and treatment process?

15 February 2024 6,732 0 View

How can I access version 4.5 of the Discovery Studio Visualizer software?

Hello I need to convert ligand-receptor interactions from 3D to 2D. But my Discovery Studio Visualizer software does not have this capability. How can I access the download link of version...

20 May 2023 7,040 1 View

Can a metal complex whose size is more than 100 nm be called a nanocomplex?

Greetings and Regards Our team has synthesized a metal complex whose size is more than 100 nm according to SEM images. Is this a nanocomplex? Basically, what should be the size of a metal complex...

16 February 2023 6,757 4 View

Why the Sediment transport rate is different for total simulation time and the accumulated monthly sediment drift rate?

Dear All, I have an issue regarding a sediment transportation simulation. I have computed the sediment transport rate based on a 20 years wave climate, and simulated the sediment drift for the...

10 July 2022 8,925 2 View

RNA seq analysis using GSEA?

Hi everyone, I have a question and I was hoping to get some insight from you. I ran RNA-seq on my samples and I didn't have replicates, I used differentially expressed genes with a cut-off of...

01 June 2022 1,349 2 View

Preparation of micro filtration flat membrane with PVDF or polysulfone?

I want to prepare microfiltration flat membranes with PVDF or polysulfone. I did the process by solving various concentrations of the polymers (from 13 to 15%) to NMP to produce the casting...

13 November 2021 6,856 5 View

TGF-β with or without carrier?

Hi everyone, I am planning to use TGF-β to transform my fibroblasts into CAFs. Most of the papers I have been reading have used TGF-β from R&D Systems, but none of them has mentioned whether they...

10 May 2021 732 3 View

Calculate sample size for diagnostic tests?

What sample size formula should I use to compare the three area under the roc curve (AUC) obtained from three diagnostic methods from similar sample? MedCalc software gives us the sample...

20 December 2020 5,862 3 View

What are the possible chelating agents to form complex with cobalt only but not nickel in the solution of nickel and cobalt sulfate?

I want to electrodeposit cobalt only leaving behind the nickel in the solution

15 July 2024 3,460 2 View

I want to ask why the poly aniline film does not stick to the ITO type substrate knowing that I used the electrodeposition method?

In order to make a polyaniline film, I used the electrodeposition method and set all the conditions, but I noticed that the polymerization process is happening, but it doesn't stick to the...

09 July 2024 2,708 2 View

PANI CV causing problem?

Hi researchers. I have deposited a polymer, PANI on Glassy carbon electrode by electrodeposition method. CV results of It showing only the oxidation peak taken in 100mM ferri+ferro solution in...

06 May 2024 9,826 3 View

Why does the redox peak disappear in CV?

Hello... I'm trying to electrodeposit at -1V with CoCl2 in aqueous solution. Is there a suitable supporting electrolyte? When measuring CV(2M KOH, Pt wire, Ag/AgCl), the redox peak decreases after...

17 April 2024 5,293 3 View

I want to know tips and tricks on electrodeposition synthesis of Cu2Te...?

I have done the hydrothermal synthesis now want to compare with electrodeposition technique.

12 April 2024 5,679 2 View

In square wave pulse voltammetry in electrodeposition?

why am I getting high evolution on the fe-co electrodeposited films with higher scan rate(50mV/S) in KOH electrolyte? what could be the reason. im using square wave pulse voltammetry

01 April 2024 4,676 1 View

In square wave pulse voltammetry deposited sample at high current density showing more evolution in KOH electrolyte . why?

pulse voltammetry using electrodeposition of Co

18 March 2024 9,760 2 View

After electrodeposition during CV cathodic peak is not seen.Why?

Iam doing electrodeposition on carbon cloth of area 1x1 cm2 and 5x5 cm2 with same volume of electrolyte and electrochemical cell(all parameters are same for both) .When doing CV of...

20 February 2024 9,896 7 View

How to dissolve tin and antimony in citric acid solution?

I am making electrodeposition liquid of tin antimony, and I want to dissolve 0.3M SnCl2·H2O and 0.03M SbCl3 in 0.3M citric acid aqueous solution, but it cannot be dissolved and white precipitate...

19 February 2024 7,614 1 View

How to pickle Ni-Plate before electrodeposition?

I have come across a suggestion to use HF and HNO3 mixture. But exact ratio is not clarified. What should be the exact ratio of these two acids to smoothly pickle Ni sheets? Any impurity in form...

24 January 2024 4,199 2 View