Could anyone give me damping property of steel?

More Ghanbar Barzegar's questions See All

How can i remove stress wave effects in dynamic explicit analysis?

Your toughest technical questions will likely get answered within 48 hours on ResearchGate, the professional network for scientists.

01 February 2016 9,520 0 View

How we can define in abaqus applying a specific load in very very little time?

how we can define in abaqus applying a specific load in very very little time? for example in 0.01 microsecond instantaneous or tabular amplitude did not response for this and after specific...

01 February 2016 2,533 7 View

How can we simulate wire rope in large scale(for example 10 m) in abaqus?

In many articles, the wire rope was modeled with solid element but this way needs high run time

01 February 2015 8,458 2 View

How can I simulate a rope in Abaqus?

Suppose one side of the rope is closed and the other side is on the pulley. Force is applied to the free side of rope. How can I simulate this, since the rope does not bear shear force? Which...

31 December 2014 9,540 2 View

Can we simulate heat transfer in beam element with Abaqus?

Thanks in advance for your replies.

31 December 2014 1,703 3 View

How can I simulate unbalancing and Gyroscopic effects in ABAQUS ?

How can I simulate the effect of unbalancing and Gyroscopic in ABAQUS ?

10 November 2014 9,479 1 View

How can I solve this Abaqus error?

HI I was encountered with this problem IN ABAQUS/ATANDARD: The executable standard.exe aborted with system error code 1073741819. Please check the .dat, .msg, and .sta files for error messages if...

09 October 2014 5,572 30 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Abhimanyu Kumar

Alpha and Beta are associated with Rayleigh damping, which can be calculated from sturctural frequencies.

Ghanbar Barzegar

hi Abhimanyu Kumar

thanks for time you dedicated to response for my question.

if it is possible please explain more and describe in detail.

it is my necessary need.

thanks