Compression deformation in Ansys has errors and not get solutions?

14 August 2020 1 6K Report

I am doing compression if High Entropy Alloy in Ansys19.2. I tried a lot of ways but it does not converge. It explodes the specimen.and show errors as well. Herewith I have attached the screenshot of the errors.

Valery Nagimovich Aptukov

Judging by the image, the boundary conditions are incorrect.

Compression, and deformations are positive?

Badges
Science topic

More Mukesh Makwana's questions See All

Why Do TDS and EC Increase with Larger Wastewater Volumes, While BOD and COD Decrease?

I have carried out MFC experiments on three different volumes, 50, 500 and 1000 mL of wastewater. Results after MFC treatment shows that TDS and EC are more in larger volumes of water i.e. TDS and...

09 August 2024 9,621 0 View

How to enrich pig excreta for increasing nutrient quality organically ?

Pig slurry is rich in major and minor nutrients. Is there any way to improve / Enrich its manure quality to be used in agriculture organically ? please share your knowledge.

09 August 2024 5,605 2 View

Is it possible to plot the atom-projected band structure using GPAW?

Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...

07 August 2024 269 3 View

Unusual intensity drop in some sections of chromatograms in DDA?

Hi, we have measured tryptic peptides using both DDA and DIA method on QExactive. In DDA replicates i saw unusual intensity drops occurring at the same sections of chromatograms in DDA replicates...

07 August 2024 3,218 4 View

Leaf area of tomato ?

Hi How can this equation Ln(LA) = 1.038 + 0.89 ln(X) be applied to calculate the leaf area of a tomato? Can you explain with an example and what is the substitution of Ln and ln?

06 August 2024 2,508 2 View

Why did the authors extrapolate a phenotype that they experimentally proved in one bacterial strain across the whole genus of the organism?

I aim to be as skeptical as possible regarding whether a pair of orthologous genes results in the same phenotype in their different but related bacterial organisms under similar environmental...

05 August 2024 6,787 4 View

How to preform densitometry on SDS-page bands?

I ran a SDS-page of a bacterial lysate and I want to quantify protein concentration in a specific band. I was thinking of using a standards ladder or make some standards are different...

05 August 2024 9,805 3 View

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds?

XRD Analysis is showing only Calcium carbonate. It is not showing other compounds. Can anyone help me get the other compounds

04 August 2024 3,019 3 View

Which solvent is better to dissolve with secondary metabolites extracted from fungi?

I work on MCF7 cell cell for anticaner purpose and I wa to do drug preperation the drug ( secondary metabolites extracted from Aspergillus) My question which solvent is better with these secodary...

03 August 2024 4,725 2 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Does anyone know, any conference related to "mathematical data compression" topic?

Please suggest me, I want to present my research work.

13 July 2024 1,461 1 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Is there any suggestion on the explanation and reduction of stacking fault defects in high Al content InAlGaAs alloy lattice matched to InP?

24 June 2024 6,645 1 View