For fast separation of oil and water, could we use PBZ-coated steel mesh? because its having more porosity.
Get more than 80% - 90% of transcription efficiency
19 July 2023 7,912 3 View
Is it possible to use In-Circuit Emulation of ARM processor to replicate the Matlab model. Is there any software to put the code into ARM chip? Please suggest on this.
25 April 2023 9,820 2 View
My own question
15 March 2023 6,905 7 View
Dear all, How to extract the strain concentration tensor while using the Mori and Tanaka formulation built into Abaqus in the input file. Please advise me on how to extract this value from the...
12 February 2023 9,791 2 View
I’m an ecologist using machine learning algorithms (using the gradient boosting approach for the first time 😊) to gain insight into land use patterns. My question is related to a machine learning...
22 January 2023 5,967 11 View
Being an essential parameter, basal velocity estimation of a valley glacier is still not significantly discussed which helps in assessing the glacier water storage capacity over a period and...
02 November 2022 8,153 0 View
How to measure/convert the Mpa (PEG-6000) to Grams? for example -2.0Mpa = how many grams?
30 October 2022 8,285 3 View
Most of the studies related to the High mountain glaciers adopt a mass conservation approach at a global level while other approaches are least adopted.
06 February 2022 9,985 0 View
Hi Everyone, We need to attach metal beads to contact lenses for a project, and I could not find any adhesive that works with contact lenses (preferably biocompatible) . I know that they are...
01 February 2022 1,887 2 View
I have been trying to check the expression of a pro-inflammatory cytokine between differentiated wild-type and knocked-down THP-1 macrophages cells. When I stimulate the cells (both at 24h and...
18 December 2021 8,298 3 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...
08 August 2024 2,298 0 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.
07 August 2024 4,526 4 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to know more about petroleum deposits in Iran.
02 August 2024 8,725 3 View
I want a model that is balanced with accuracy or speed, faster rcnn has high accuracy while yolo have fast speed. i am thinking to combine them to get a hybrid model to achieve both speed and accuracy
02 August 2024 3,104 0 View
Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container
30 July 2024 7,326 1 View
I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...
30 July 2024 3,294 3 View