Calculate sample size for diagnostic tests?

What sample size formula should I use to compare the three area under the roc curve (AUC) obtained from three diagnostic methods from similar sample? MedCalc software gives us the sample...

20 December 2020 5,635 3 View

Dose any-one knows about cleaning validation for pathogens from fermentor?

Hi Dose any-one knows about cleaning validation protocols for pathogen-bacteria from fermentor? In industerial size, 1000 lit?

15 December 2020 4,418 3 View

How can I model mechanical properties of a material using Von Misses-Hill model in Abaqus?

Hello everyone; I am trying to simulate a stent which is made of stainless steel in abaqus and in addition to the elastic properties that are defined by Young's modulus and Poisson's ratio I need...

15 September 2020 1,809 4 View

How can we calculate the concentration of 1000 tons of carbon dioxide in the air in PPM?

Dear All scientists; How can we calculate the concentration of CO2 emitted in the air in PPM? shall we use PPMv(Volume PPM) or Mass PPM is also acceptable? Regards

01 August 2019 7,464 4 View

How can I recall a modified citation style in Mendeley with the name I entered?

When I save as a modified style and change its name, the new style does not show up with the name I have entered for in the styles list. In stead, a general title like "APA-Saeideh" is built...

20 May 2019 6,622 6 View

How can implement print screen key action in c# ?

We can implement for example enter key in c# by SendKey.Send( {"ENTER"}) code. but this method didn't have option for print screen key (reserved for future use ). how can I implement it? My...

29 January 2019 6,161 1 View

How do you control the cancer?

25 October 2018 7,240 3 View

Economic evaluation modeling based on secondary data; which of the following approaches is accurate?

I need to run an economic evaluation model of 6 drugs based on secondary data of a network meta-analysis study which has covered 21 drugs. This study also has reported separate pairwise head to...

03 September 2018 3,174 1 View

Can I run GEE having two within factor variables?

I have one factor as time (3 time points) and the other as treatment( absorbable versus nonabsorbable Sutures that each of them were used on different sides of a scar) so two treatments had been...

08 June 2018 6,220 1 View

How can I make a teeth whitener in the chemistry lab?

How can I make a teeth whitener in the chemistry lab?

02 June 2018 6,306 3 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View