Is the term genome applicable to all ploidy levels?

09 October 2018 8,051 6 View

Is there an arbitrary classification for the total phenolic content (%w/w)? How high is high? how low is low? are there any standards in classifying?

I am currently having conduct a study regarding the total phenolic content of a plant extract; however, I cannot determine if a 42.7 mg/g gallic acid equivalent phenolic content is high or not.

07 August 2018 4,260 4 View

Oil content determination using oven dry method?

I want to ask if determining the seed oil content using gravimetric means such as done in the paper below is appropriate. There were no chemicals used. I could not find any other literature...

02 March 2018 7,186 4 View

Does freeze drying and storing plant tissues in -80 deg. C affect the total RNA yield in RNA extraction?

It is because I have very low RNA yield. I was thinking if it is because I use 1-week old freeze dried samples stored in the freezer at -80 degree celsius. Amybe it is better to use fresh samples...

06 July 2014 6,395 10 View

In spectrophotometric analysis, what would a >2.0 260nm/280nm absorbance ratio of an RNA extract indicate?

My hypothesis: Since nucleic acids has a peak absorbance at 260nm wavelength and proteins at 280nm, the ratio of greater than 2.0 is considered relatively pure RNA. Twist: However, literature...

05 June 2014 1,124 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View