Can Magneto-rheological fluids simulation be done using ANSYS?

More Saravanan R.'s questions See All

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

Is there any cases algae not using the nutrient from the wastewater and grow normally?

I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...

08 August 2024 4,812 2 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

Articles on" Gender disparities i leatherwork education"?

Articles on" Gender disparities i leatherwork education"

07 August 2024 2,500 0 View

Why results of ROS flurescence are negative as there was no bacteria within?

Hello. I am working on ROS production of two systems: system A is cerium oxide and hydrogen peroxide, system B is cerium oxide nanoparticle, hydrogen peroxide and potassium bromide. I did some...

04 August 2024 5,974 3 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Why reactivity isn't increased with more empty spots in valence shell?

If from a geometric perspective the non-halogens, non-noble gases have more empty spots in their valence shell, and the filling/exiting of any of the empty spots in the shell constitutes a...

03 August 2024 4,787 2 View

Why is the molecule's orientation with an electric field affect polarizability?

Why is the molecule's orientation with an electric field affect polarizability? Electrons are diffuse enough to be independent with respect to orientation and effect of electric field on...

03 August 2024 7,843 1 View

Why don't d-orbitals split themselves, why does it take a ligand? why don't protons from ligand repel nucleus split d-orbitals?

why don't d-orbitals split themselves because of themselves without the presence of ligands? Electrons are indistinguishable. Why wouldn't it be more correct that protons from a ligand split the...

03 August 2024 3,589 3 View

Why doesn't chromium 2+ ion use all its d-orbitals to receive lone pairs from six waters in [Cr(H20)6)]3+?

I'm guessing it's because the ligand experiences too much electron repulsion or proton repulsion from the chromium to insert them close to the 3d-orbitals which are close to the metal nucleus. Is...

03 August 2024 1,370 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Ethylene glycol is newtonian or non newtonian fluid?

Some sources say it is treated as Newtonian as ethylene glycol has a higher viscosity than water, which affects the flow characteristics in simulations. But some also say it is non-Newtonian.

09 August 2024 2,111 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

If modulus of elasticity is divided by any inertial or dynamic pressure (1/2rhov^2), is there any dimensionless number present to represent it?

While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...

23 June 2024 8,059 1 View

R.D.Vignesh devendiran

hi saravanan , "All the best for your project".i don't know whether the MR will be analysed in ansys. but i gave one suggestion.please refer the CFD softwares.

once again "congrats" for your current status.KEEP TRYING

Hemnath A K

It is possible to do in COMSOL it seems. Please look at the link below.

https://www.comsol.com/paper/modeling-flow-of-magnetorheological-fluid-through-a-micro-channel-6630

Saravanan R.

Thanks for your information sir.