Can I use phase field to model Reinforced Concrete Beams with Abaqus program?

Hanadi Lateef @Hanadi-Lateef

01 January 1970 1 7K Report

Hanadi Lateef

thanks so much

Badges
Science topic

Similar topics
Computer Science
Program

More Hanadi Lateef's questions See All

Merge Intensity Data from 2 runs?

Hi, We have collected several images for two independent runs of an experiment using two different confocal microscopes and settings. Thus, the intensity values collected through ImageJ were...

22 July 2024 8,722 0 View

Why I have this weird green signal in the nucleus?

Hi, In a few wells and cells, we’ve noticed an unusual signal in the nucleus using both eppifluroscence & confocal microscopes. Does anyone know why this is happening? It occurred twice in...

10 July 2024 1,870 0 View

Post earthquake fire analysis in abaqus?

what steps do we need to perform the fire analysis on the steel structure already subjected to earthquake in Abaqus?

13 May 2024 9,786 6 View

Push over analysis in abaqus?

What values of lateral load we need to use in order to perform push over analysis in abaqus for a high rise steel structure?

07 May 2024 6,111 2 View

The importance of the PMO Project Managment Office for the public sectors?

Public sectors need improvement in the way they manage their projects. most of the projects don't achieve its goals.

02 April 2024 9,798 5 View

How can I separate 1 tile image into separate images?

Hello, We used Zeiss LSM880 & Zen software for tiling images, scanning approximately 32 areas in one tile image. How can I save these 32 images individually, not as a tile image? Attached is...

11 March 2024 783 2 View

Why I had empty wells in 7 out of 8 after performing Immunostainong protocol?

I followed an immunofluorescence staining protocol for my cells differentiated into neurons at D14. Using 4% PFA (Alfa Aesar product) for fixation in PBS, I observed that 2-3 out of 8 wells were...

02 February 2024 8,932 10 View

How can one quantify the number of particular cells exhibiting a signal within FL images out of the total cell population using Fiji/ImageJ?

Hello, We conducted three stains for Nucleus, Outer membrane, and a particular phosphorylated protein expressed in a subset of cells. After capturing random images, our focus is on enumerating...

01 February 2024 6,079 1 View

What are most needed epigenetics evaluation techniques?

Dear All. If a researcher wont to conduct an article to evaluation an axpected noval epigentic compound, what is the most essential steps of techniques that should followed to optimised his...

21 December 2023 7,007 3 View

Why perovskite layer does not adhere on TiO2?

I am working on lead-free perovskite solar cell, TiO2 is an ETL that has been prepared by RF sputtering. I have noticed that perovskite layer did not adhere very well on TiO2 surface and the...

14 November 2023 945 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to solve g_mmpbsa error?

Program: g_mmpbsa, version 2024.1 Source file: extrn_apbs.cxx (line 152) Fatal error: Failed to execute command: $APBS pybYcUWA.in --output-file=pybYcUW.out

07 August 2024 6,066 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View