Can i use hatta number for second order reaction in solid-gas water film to find the mass transfer coefficient?

Wan Nor Nadyaini Wan Omar @Wan-Nor-Nadyaini-Wan-Omar

18 April 2018 0 2K Report

I found that the hatta number usually used for second order reaction in gas-liq study.

Therefore, I wonder if i can use hatta number to study the mass transfer in solid-gas that has water film in surrounding of the particle? The reaction is second order.

Badges
Science topic

More Wan Nor Nadyaini Wan Omar's questions See All

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

Why does flow deformation occur at the test line and control line on nitrocellulose membranes (LFIA)?

I use 1% BSA in 10 mM phosphate buffer (pH 7.4) solution when striping my nitrocellulose membranes with antigens and antibodies. However, I always observe deformed flow when my sample or running...

16 February 2021 4,224 3 View

How to avoid polypyrrole deposit on counter electrode?

Hi all, Currently, I electrodeposited polypyrrole on carbon electrode but I got some problem when polypyrrole also deposited on the surface of the counter electrode. The concentration of pyrrole...

05 February 2021 2,103 3 View

How can I set up UV irradiation for crosslinking lab?

Hi, I am using a mix of 2 polymers and want to try and crosslink them. I have a UVA lamp of 365nm and have tried the lab previously at 30cm above. How would you recommend I approach the lab and...

31 January 2021 8,711 3 View

Which air pollution/air quality books do you recommend for working with environmental engineering students?

I am exploring up-to-date books on air pollution and air quality, and I would like to know which books do you recommend for environmental engineering students.

25 January 2021 3,972 7 View

Orbitrap Fusion FT keep getting disconnected?

Hi, I been having a problem with the Orbitrap Fusion for quite a while and it has been getting more and more frequent, which is very frusttrating. The fusion FT would get disconnected suddenly...

22 January 2021 1,235 4 View

How to simulate Sloshing water using Dynamic mesh in ANSYS Fluent ?

I am trying to model sloshing water in a tank in ANSYS Fluent using Wall motion. BUT it seems that System coupling is not responding to wall motion and it works only with Dynamic mesh.

20 January 2021 2,963 3 View

What is the basis set to optimize ZnO using GaussView for DFT calculation study?

Greetings, I have a bit of problem in setup the basis set of my DFT study for ZnO.. As you can see in the image attached below, I use B3LYP 6-31G (d,p) for geometrical opt. of ZnO.. But sadly, I...

13 January 2021 7,508 4 View

Are there other models that meet the same purpose?

Both Jakes and Gaussian models are used to characterize the power spectral densities of mobile communication channels.

11 January 2021 759 3 View

How does titanium dioxide (TiO2) as a coating's component enhance the coating performance in terms of anticorrosion??

Greetings, Recently, I was asked by a researcher how does TiO2 enhance the coatings polymeric structure making it able to reduce corrosion reaction by preventing the penetration of aggressive...

02 January 2021 5,257 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Discrete Phase model (DPM) particle break-up has particle size limits during particle tracking?

Hello, I am currently working on simulating water droplet partciles in a closed room. When I use uniform particles, without "particle break-up", I can carry out the simulation without any problem....

02 March 2021 3,053 2 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

Distribution of particles in metal matrix?

How would define the "good" and "poor" distribution of particles within the matrix. Is there a quantitative solution to assess the distribution of the particles, which then having denotation of...

28 February 2021 7,397 8 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View