I want to use electrospinning technology to make collagen and PLGA nanofibers. I used to use DCM and DMF as the solvent to dissolve collagen, but I did not find any Nitrogen from EDS.
Good day! Hope that following articles will help you to find a solution.
https://www.mdpi.com/1996-1944/10/7/693
https://www.scientific.net/AMR.849.337
https://www.researchgate.net/post/How_can_I_mix_PLLA_solution_with_collagen
https://bradscholars.brad.ac.uk/handle/10454/16998
Article Luminescent Biofunctional Collagen Mimetic Nanofibers
zebrafish and mouse
19 July 2024 9,158 1 View
Dear scientific researchers, may I ask you, what is the function of the ∑ in the picture?
10 July 2024 2,037 3 View
We have observed many holes on the surface of TiO2. These holes have a diameter of approximately 1 µm and a depth of about 30 nm. The formation of these holes is mainly related to the...
20 June 2024 3,861 1 View
What kind of cases are geometric phases real? In what case is the geometric phase complex? If the geometric phase is complex, how do we make sense of it?
18 June 2024 6,388 4 View
I used SD rats (E19) for cortical neuron extraction. Due to the need for subsequent special experiments, I cultured the neurons in a Corning PDL 384-well plate. The culture medium is Neurobasal +...
12 June 2024 1,714 4 View
XRF tests were performed on magnetite where the oxide content showed 49.822% Fe2O3, so why not Fe3O4 content as a percentage? How can we deduce the Fe3O4 content?
25 May 2024 1,714 2 View
Since the acoustic impedances of air and solid medium are not in the same order, the acoustic wave transferring in the air would be theoretically fully reflected on the solid surface. So my...
21 May 2024 6,858 9 View
Asking for help: Dear academic experts, does anyone have data on girth weld failure?
07 May 2024 9,666 1 View
Are there any group chats or websites recommended for soil contaminant degradation? Thank you!
26 April 2024 4,887 1 View
How Dynamic Bayes can be better integrated with cloud models for risk assessment
25 April 2024 5,630 2 View
How can the rubber fibres produced by the electrospinning device be removed from the fibre collector (aluminium foil) without affecting the orientation of the rubber fibres for use in reinforcing...
26 July 2024 8,281 0 View
Kindly share a research paper that explains the effect of Methanol and ethanol treatment on collagen based scaffolds. How it increases porosity and swelling. Kindly help me find a paper. Thank you
24 July 2024 3,937 0 View
I am experiencing this for the Bi2Se3 sputtering target. Initially, even if the target was 2:3 in Bi : Se, with a few sputtering runs, due to the high escaping tendency of selenium, the top layer...
23 July 2024 1,649 1 View
Hello everyone, I work with polyacrylamide hydrogels, which I fictionalise with sulfo-sanpa and collagen I to then plate lung cancer cells. The problem is that I lose a significant amount of...
19 July 2024 3,906 0 View
Dear all, I have a difference in the weight ratios between EDS mapping. What should I rely on? Is there a way to solve this problem?
12 July 2024 305 1 View
Recently, we measured EDX/EDS of LaCrO3 crystals synthesized by hydrothermal method, and found that the characteristic energy for La and Cr are nearly the same for all of the noted energy levels....
02 July 2024 4,587 6 View
Hello everyone, I'm facing an issue with EDS software that prevents me from obtaining atomic or weight percentages for my scan. However, I do have access to the raw data, which shows intensity vs....
29 June 2024 6,664 14 View
I'm trying to submit a paper, but two different manuscripts are being prepared. One is by me and one is by a collaborator who is using my samples. I know it's unethical to reuse the same data in...
25 June 2024 6,110 2 View
I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...
17 June 2024 9,763 0 View
Hello I am encountering Fe and other stainless steel (SS) element contamination in my LiCoO2 RF sputtering depositions. I suspect the source is the "etching" of the magnetron stainless steel frame...
11 June 2024 2,196 3 View