Can anyone tell me how to clean ITO coated glass for sputtring magnetron deposition? - FAQS.TIPS

Mohsen Vaezzadeh Asadi @Mohsen_Vaezzadeh_Asadi

10 October 2018 0 2K Report

Dear colleague

Can anyone tell me how to clean ITO coated glass for sputtring magnetron deposition?

Badges
Science topic

More Mohsen Vaezzadeh Asadi's questions See All

Is there a mathematical relation between defect density and temperature?

Is there a mathematical relation between defect density and temperature? thanks

03 April 2019 2,612 3 View

Have thermal velocities electron and hole in semiconductors constant?

hi have thermal velocities electron and hole in semiconductors constant? What are they calculated? thanks

01 February 2019 3,256 3 View

What is the condition of plasma formation for titanium dioxide?

hi What is the pressure of plasma for the Titanium Dioxide layer under RF Sputtering?

31 December 2018 8,277 3 View

Do the following things change and how much?

hi, pleased guide me if i change thickness of different layer perovskite solar cells , or Physical conditions of making layers such as Change in pressure,Change in temperature sunstrate,...

10 November 2018 640 4 View

I made a thin layer of titanium dioxide in the lab. What methods can now be used?

Hi, I made a thin layer Tio2 in the lab. what methods can now be used to to determine lifetime of the carriers ( e and h ) , their mobility , and the concentration of the carriers ( NA , ND)? thanks

10 November 2018 1,278 4 View

What is stack of HAADF STEM cross section image?

what is stack of HAADF STEM cross section image?

10 November 2018 787 0 View

How should be simulated layers with comsol software?

Hi, I want to use comsol software to simulate provskite solar cells, I dont know what kind of information is needed to simulate different layers and finally extract the best power converting...

10 November 2018 3,643 1 View

Does anyone have this book?

Dear partners Does anyone have this book? quantum theory of the optical and electronic properties of semiconductors 5th edition , hartmut huang and stephan w koch thanks

08 September 2018 9,600 0 View

What is the best conditions for the titanium dioxide present at the temperatures of the RF sputtering?

hi, Please advise. What is the best conditions for the titanium dioxide coating at what temperatures and under what physical conditions (pressure, ...) is the RF sputtering method? sincerely yours

07 August 2018 5,175 1 View

What is the use of Comsol software in Provskite Solar Cells?

Advise you. Has anyone simulated Provskite solar cell with Comsol software? What basic information is better to enter in this software? The thickness of the layer?, the temperature substrate?,...

06 July 2018 9,903 3 View

Similar questions and discussions

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Fabrication of narrow glass capillary (inner diameter 200~500 nm)?

I need a very narrow glass capillary for my research. How can I make a glass capillary with an inner diameter of around 200 to 500 nanometers?

08 August 2024 8,915 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

Dirty and clean?

Hi everyone I need a file with a dirty and clean potato image

04 August 2024 7,199 4 View

How to clean the CAD detector?

The module of the CAD detector is corona Veo. It has been idle for a long time. And it was not well maintained before idle. I have replaced the gas filters and flushed the system with a 50/50...

01 August 2024 7,805 0 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Which filtration method to go for run off water from dirty solar panels to be used again?

We are working on a robot that cleans solar panels using fresh water supply and a rotating brush. We are trying to conserve as much water at possible by recycling the dirty water that is collected...

28 July 2024 5,778 2 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View