Can anyone suggest to me the deposition parameters for ZnO and AZO thin film on glass with thermal evaporator (from Powder)?
This Paper very good for you, is attached
(International Journal of Photoenergy
Volume 2014 (2014), Article ID 406495, 10 pages
http://dx.doi.org/10.1155/2014/406495)
I think you will find your answer in it.
Best regard
Dear, see the researches of Nadir F. Habobi on research gate.
Dear, maybe chemically interest from this attached research.
Thanks alot for your kindly answer
Hello everyone, We have a water treatment unit where the input water is TAP WATER. Tap water pass throw three steps in this order: Softner ==> Filters (cotton filter+charcoal filter) ==>...
02 January 2024 5,900 9 View
After several washings of shale samples in search of microfossils, each time we obtained the same results, a species of foraminifera and radiolarians, we followed the standard method, with water,...
17 November 2023 3,037 3 View
17 November 2023 2,638 1 View
Hi all, I am trying to work on this subject for my Ph-D and I would apreciate if anyone could help me to know who are the most imporant authors that worked on this topic. Even those who worked on...
24 October 2023 8,625 4 View
I have field data for random samples from a specific forest, represented by vegetal surveys, where each vegetal survey contains one, two or three dominant vegetal species with geographic...
02 October 2023 4,291 1 View
Does the % peak area of a GC/MS chromatogram correspond to the mass percentage?
03 September 2023 6,924 5 View
Please needs to explain: The relationship between the great inhibitory zone (in antibacterial activity) and the lowest or greatest MIC, Why? Thanks
15 August 2023 6,688 6 View
post graduate studies often done in English and most papers are published in English. student all over the world take fondamental programs in their mother language, hen they reach to the reserch...
13 August 2023 3,690 2 View
the volume in the equation refer to the volume of extract needed for the assay (0.1ml) or is it the volume total of my extract (5ml)? also, the concentration of my extract is 50mg/ml so I make a...
21 July 2023 5,445 1 View
I should realize a GC-MS analysis for a fixed oil, and to avoid the worse injection volume of both (volume of sample and the solubilizing solvent), I need some guidelines by researchers. Thanks in...
15 May 2022 507 2 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I have been using paraffin, but the deposited ZnO still detach from electrode. What is the best binder to modify graphite paste electrode with ZnO nanoparticles?
03 August 2024 4,624 3 View
99% pure ethanol was used for maceration also alternate methods along with the temperature and time to concentrate the extract can be specified
31 July 2024 5,113 4 View
Dear all, I have noticed, as the ZnO content increases, the Raman intensity at 100cm-1 also increases. However, there is a peak nearby at 130 cm-1, which I could not find in any paper related to...
28 July 2024 5,410 1 View
I have different polymer solutions and I hypothesize that water molecules are retained based on the water-polymer interactions, so the amount of free water is less to intercat with drug tablet....
28 July 2024 9,545 6 View
What is the thermal expansion coefficient of human muscle?
27 July 2024 7,190 0 View
Recently I have submitted an article regarding MB dye degradation by ZnO nanoparticle. I received a suggestion to include the discussion on the effect of pH. I want to know what is the impact of...
19 July 2024 4,868 1 View
I want to extract glycosides from my mangrove leaf samples, but my laboratory lacks an incubator capable of reaching temperatures above 60°C. The paper I am following specifies a minimum...
13 July 2024 3,686 0 View
"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...
13 July 2024 8,621 5 View
We're studying the stability and fusion behavior of multiple PVC compounds in a Brabender. After a few trials, we set the temperature at 195 °C and the rotor speed at 70 rpm. Samples differ in...
12 July 2024 2,768 1 View