I would like to plot thickness distribution of formed part using Continuum elements in Abaqus...
Hello dear Elangovan.
I thik that you search an equivalent of Sth in shell domain , for the 3D model in abaqus simulations.
There is no equivalent output of thickness for 3D mesh , but you can built a method :
1 : as a normal distance between 2 outer sides of continum part, finer mesh gives accurate thickness .
2 : Calculation from mesh sizes and normal strain thickness output.
3: Developping a python file tracking alghorthm of normal distance.
Best wishes.
Thanks Selmi
Is it possible to find in fluent? Any other method is there?
10 September 2020 5,492 3 View
I have collected a 30-minute HRV during a stressful task for two different groups. To compare the variations, i have seen many papers average the hrv over the collected time. Is that a right...
03 October 2019 9,174 1 View
Here I mentioned only Glass rod and silk cloth. This can be anything from triboelectric series. But, why should it happen? Why should different charges accumulate in two materials and then...
22 August 2018 2,619 2 View
Hello Everyone, I am Venkat and am trying to work with cells and tissues from the aorta. I am hoping to study telomere lengths from my samples and I was wondering if there were a reliable way to...
07 December 2017 8,250 7 View
19 July 2017 1,236 3 View
When the ORR catalyst i synthesized gives five times greater current density than the commercial Pt/C, then the slope of the KL plot for the catalyst synthesized will be higher because of the...
24 July 2016 1,504 2 View
Computational Electromagnetics
18 January 2016 1,190 5 View
To import mesh with pre-stress values into ANSYS?
26 January 2015 671 3 View
I would like to carry out structural simulation without defining material property in Ansys (Stamping mesh with pre-stress).
21 August 2014 8,522 1 View
TiNiSn is a Half-Heusler alloy with VEC = 18.
28 May 2014 1,428 2 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View
I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...
01 March 2021 736 3 View
Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...
01 March 2021 9,511 3 View
Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...
28 February 2021 3,442 2 View
I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...
28 February 2021 4,841 3 View
I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...
28 February 2021 5,415 1 View
I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...
27 February 2021 6,818 3 View
Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...
25 February 2021 9,936 2 View
I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...
24 February 2021 4,908 5 View