Can anyone help with optimized crystallographic files of MAPbl(3-x)Clx, MAPbCl3 ? (Mixed Halide Perovskite)

More Samuele Lilliu's questions See All

Best mounting medium for plant-tissue coloured with WGA-AF488 staining?

Hi everybody, I am preparing some plant tissue microscope slides, and I am doing a specific staining for fungi coloration (WGA-AF488 in PBS buffer pH 7.2). I was wondering what would have been...

26 November 2020 6,118 3 View

How to model a graphite-bearing rock using Perplex (pseudosections)?

Dear all, I am struggling to model a rock which contains the assemblage K-white mica + Na-white mica + chlorite + quartz + graphite + rutile. I have followed step by step the tutorial available on...

22 November 2020 2,387 2 View

How can I convert emuOe/g in A/m?

From a research I got the saturation values of an MH curve in "emuOe/g" but I need them to be in A/m. My doubt here is is the data in "(emu/g) * Oe" or that "emu" means only "electromagnetic...

30 June 2020 2,356 8 View

How to stop enzymatic reaction without hurting bacteria?

Hello everyone. I need to test a reaction mix against bacteria, to state its inhibitory potency: how can I stop the reaction? I tried filtration using MicroCons, but part of the product is lost,...

09 January 2020 9,909 3 View

Does anybody used Assess 2.0. Image Analysis Software?

I analized six sets of 26 leaves using the same process with the Automatic Panel. I used the same thresholds and the same calibration for all of them. In only one of the sets the data are...

15 January 2018 3,627 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View