In the UNDEX simulation on a simple steel plate, the stress in the plate does not converged but the pressure of acoustic medium reach a peak and converged. I put the pictures below. Does any one know why it is happened?
Not really enough information to understand your problem let alone help you with it. Why don't you post a short document of explanation?
There are many Finite Element softwares that are some commercial and some not. Many of them are open-source and some are closed-source. Abaqus, Ansys, LS-DYNA and ADINA are familiar to all...
09 October 2015 2,292 8 View
I want to analyse an explicit model in Abaqus software, but because of consuming time, I want to use Parallelization. I read the help but it runs just with two nodes. what settings, I should do to...
08 September 2014 7,416 2 View
I want to write a VUMAT subroutine for progressive impact damage. In a failure criterion, there is a characteristic length. How can I calculate this? A friend told me to write the element length,...
04 May 2014 6,864 7 View
I want to implement a VUMAT subroutine in Abaqus, but when I do it, the following error displays. Is there anyone who knows what this means? I use Abaqus 6.12-1 and visual studio 2008. I am sure...
04 May 2014 2,152 30 View
I want to model progressive impact damage in laminated composite, I see in papers, they usually use VUMAT subroutine, but there are other subroutines to model damage. Is there anyone who knows...
04 May 2014 2,899 2 View
I don't know anything about damage theory, but I must model damages in composite materials. Do you have any tutorial, book or anything to help me?
02 March 2014 1,926 7 View
I want to model low velocity impact damage in composite plates. I don't know anything about it. Could anyone help me? Tutorial, book or etc.
02 March 2014 691 15 View
I wanna to analyse a low velocity impact procedure on composite pressure vessel, but I don't know what analyse I should be do. Can anyone help me?
01 February 2014 6,758 23 View
I want to know where they are used exactly.
01 February 2014 5,964 11 View
In an impact analysis, there is a curve that shows residual tensile strength of composites that has incurred damage due to impact. You can see this curve in attachment.
01 February 2014 2,576 1 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View