The sample contains Ni, Ti, Sn.
I cannot identify the pics at 31°, 32.4 and 45.3°.
in attachment the xrd pattern
Best regards
What is exact chemical formula of your sample? Without knowing chemical formula one can not able to identify the peaks.
@ Dinesh Kumar
One of XRD tasks is identifying unknown crystalline materials.
My simple consist of the product of milling for 30 min of the elemental powder of Ni, Ti, Sn.
Using highscore and ICSD database I have identified the pics of these three elements, but the pics at 31°, 32.4 and 45.3° remain not identified.
Dear colleague, in such a case you need the composition of the mill or mortar. Blank values have to be determined. A good option to get blank values of your system is using purified quartz sand. Good luck!
Alex
It looks like these peaks (31°, 32.4 and 45.3°) are explained by a Tin Beta phase (98-023-8883), See attached screen shot of PhaseID
Thomas Degen I am grateful for your help.
Can I know which database have you used ?
I was using PANICSD 2017-1 and PDF4+ 2018. The Tin-beta card is "98-023-6663" by the way.
I didn't check if one of those databases would have been enough already to solve that case.
It is solveable by using the PANICSD only, see screenshot:
I was actually using pretty strong elemental restrictions bringing down the search space to 1153 reference patterns only, see screenshot:
I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...
08 August 2024 4,812 2 View
FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion
25 July 2024 2,486 2 View
I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.
23 July 2024 3,654 2 View
In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...
11 July 2024 4,163 4 View
What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?
08 July 2024 7,464 1 View
How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...
08 July 2024 6,609 2 View
what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?
08 July 2024 7,869 1 View
In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...
26 June 2024 6,941 3 View
Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...
23 June 2024 4,763 0 View
I'm thinking of how to increase biomass to replace plastic and industrial waste.
23 June 2024 1,871 4 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Require for Rietveld refinement in XRD.
08 August 2024 3,081 2 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View