Can anybody advise on how to clean a JIMA resolution pattern to remove deposited dust/lints etc.?

22 September 2014 1 9K Report

Is a chemical cleaning with alcohol OK?

If it's only dust, you probably don't even need alcohol. Have you tried carefully dusting it off with clean (!) compressed air?

Badges
Science topic

More Ashish Kumar Agrawal's questions See All

Why might the impedance values for DI water and 0.1X PBS buffer solution exhibit a decreasing and increasing trend, respectively over time (HP 4194A)?

Hello everyone, I'm encountering an issue with my electrochemical impedance spectroscopy (EIS) measurements and would appreciate some insights. Experimental Setup: Electrodes: Gold interdigitated...

05 August 2024 3,783 2 View

Which test should be used to study association among demographic profile and awarness level?

i have to study the awareness and adoption level of cloud computing in a district of India. i also want to use association among demographic variables like gender, age, education, income etc and...

02 August 2024 2,420 3 View

Tissue homogenization in mouse with FastPrep-24™ 5G - is the D matrix system useful?

I need to lyse and homogenise mouse tissues. So far I have experimented with liver and lung tissue, using matrix D. The liver was completely lysed with 6 repetitions of the standard program, but...

31 July 2024 9,186 0 View

What is the relationship between the threshold voltage and the device's noise performance, particularly in terms of flicker noise and thermal noise?

The threshold voltage (Vth) of a MOS device plays a crucial role for its operation. At the same time, noise is an intrinsic factor. So how noise (flicker or thermal) change with the change in...

29 July 2024 3,246 0 View

Should Coefficient of Variation (CV) in a biological data necessarily be below 30%?

In a research, lesion diameter due to a disease has a CV below 10%. However, in an another parameter, disease inhibition percentage (compared to control), a value derived from lesion diameter...

27 July 2024 201 0 View

Single crystal X-ray diffraction data solution?

I am working in metallosupramolecular single and multi-cavity cages. I am seeking a person who can help me to solve the single-crystal X-ray diffraction data.

08 June 2024 4,128 1 View

Does the first semicircle represent contact resistance, and what is the reason for its generation?

My research topic is the corrosion of gray cast iron in methanol. EIS measurements were conducted at open circuit potentials (Eoc) using a sinusoidal signal with the amplitude of 10 mV from 100...

05 June 2024 6,891 2 View

How to simulate plasma jet by COMSOL?

In COMSOL, how to use the gas concentration distribution results obtained by steady-state calculation as initial condition for plasma module for subsequent calculations? The commonly used data...

09 May 2024 7,335 0 View

How to analysis Mossbauer Spectroscopy data?

Scenario: I got two data files (α-Fe and Fe-containing samples), and the file names contain the max velocity value. Confusion: 1. How should I plot the X-axis? Is +/- velocity with points...

07 May 2024 3,244 0 View

How to extract bioactive compounds from fungal cultural filtrates...? Which of the techniques are best for the isolations...?

simply asking about the isolation of the pure compounds of fungal cultural filtrate as like the distillation of the essential oils..

06 May 2024 2,110 3 View

I need JCPDS file of LSFCO nanomaterial. Can anyone provide me?

Require for Rietveld refinement in XRD.

08 August 2024 3,081 2 View

How to understand this crystallographic phenomenon of low temperature crystals in zeolite?

During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...

06 August 2024 726 3 View

How to fix background error in rietveld refinement of one XRD peak using GSAS-II?

I want to refine one XRD peak of my in-situ xrd but the background is never working good which ultimately fails the refinement. How to refine and adjust the background using GSAS-II

05 August 2024 5,291 2 View

Dirty and clean?

Hi everyone I need a file with a dirty and clean potato image

04 August 2024 7,199 4 View

How to calculate the molar proportions of the oxides from the XRF analyses?

02 August 2024 2,565 2 View

Hello, regarding Mxene 2D titanium carbide?

I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.

02 August 2024 6,789 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

How to clean the CAD detector?

The module of the CAD detector is corona Veo. It has been idle for a long time. And it was not well maintained before idle. I have replaced the gas filters and flushed the system with a 50/50...

01 August 2024 7,805 0 View

How to find projects for a team of professional developers in AI?

We are looking for projects for a team of professional developers About us We are a team of experienced developers with over 10 years of experience in various programming fields. Our mission is to...

30 July 2024 8,377 0 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,261 4 View