Can any one tell me, while giving the load in the connecting rod in Ansys, which is the exact point to give load and which is the exact point to fix?

More Yuvraj Balakrishnan's questions See All

Is hardening is the necessary process in Aluminium LM6 tensile specimen?

do ASAP

02 March 2015 5,532 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Zol Bahri Razali

Very Interesting question, similar to my case. Could you check one of the spesial journal in .... (lets me check first....)

Nirajkumar Mehta

Connecting rod works under the condition of tension and compression. If you are doing static structural analysis, then you can consider area in the contact with piston as fixed and area in the contact of crack shaft under force.