Can any one help in Proton exchange membrane fuel cell simulation using ansys?

i have designed geometry in solid works i need help in ansys now. should i go for importing into ansys design-modeller or directly defining fluid and solid domain in solid works than into ansys...

06 July 2018 771 2 View

How to use genetic algorithm to find wake effect of wind turbine?

03 April 2017 7,078 6 View

What are the key steps to analyze the wind data after importing the data into matlab?

.

02 March 2015 7,686 1 View

How can I import wind data into matlab?

While analysing wind data stability using disttool and dfittool commonds in matlab we have to import our data into matlab.i am having problem in imoprting data into matlab because i of either wind...

01 February 2015 7,834 8 View

How can I use the loops in matlab to get better results from the plotting?

08 September 2014 3,785 4 View

Hi is there any one who is related to field of laser micro/nano fabrication?

Need help and study material regarding above mentioned topic.

01 January 1970 7,836 0 View

How two melting peaks in DSC of polypropylene can be merged into one crystallization peak?

The figure shows DSC cooling (blue) and 2nd heating (green) curves (step: 10 K/min) for a commercial sample supplied as Atactic Polypropylene (APP). The heating curve illustrates two major...

03 March 2021 5,857 3 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

Help request in CST microwave?

im working now on TPV solar cells and metamaterials and i realy need our help in CST microwave i have a tpv cell simulation and i want to extract particullarly the absorbtion of only the active...

02 March 2021 2,246 2 View

Anyone found any research papers on solar furnace design calculations (for solar concentration)?

I am thinking about working on solar furnace with heliostats that concentrate sunlight and heat molten salt, but currently no luck with research. Not a lot of papers based on the subject. (check...

01 March 2021 5,023 5 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

How to size battery banks?

I am designing a small grid connected solar PV power-plant. As the battery's capacity is specified in Ah and demand in kWh. What is the best way to size the battery bank? I have battery price in...

28 February 2021 1,638 3 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View