Can a PLS-DA model result in values of specificity and sensitivity which do not match the data in the confusion matrix or table?

More Mudassir Arif Chaudhry's questions See All

For a PLSR model how can I view the RPD values in the PLS toolbox? Or the only option I've in this case is apply the formula 1/√1-R^2 ?

I can't find the RPD value in the PLS toolbox. I'll be grateful for the guidance. Thank you

08 September 2016 7,849 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Kyle Doty

One thought is that the results in the table or confusion matrix are for calibration whereas the sensitivity and specificity values are for internal cross-validation (CV). What are your sensitivity and specificity values? Are they off by a substantial amount?

Mudassir Arif Chaudhry

Actually the formula for the sensitivity is not satisfied by the result. For classification purpose the formula says (total number of correctly classified samples in a class/total number of samples in that class). If all the samples in a class are correctly classified then the value of sensitivity should be 1.000 but it appears around 0.800. Can you guide me please?