Bridge Vehicle Interaction Model?

17 June 2022 0 6K Report

I want to know how to perform bridge vehicle interaction model in ANSYS ? What are the steps to be followed. Please suggest. If required you can contact me at- [email protected]

Badges
Science topic

More Om Narayan Singh's questions See All

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

How to increase citation in Research Gate?

How to enhanced h-index in Research Gate?

04 August 2024 3,368 4 View

How to do wavelet transform of EXAFS data?

I want to do wavelet transform of some compounds for their comparative study? Kindly help me in this regard and provide with proper procedure.

31 July 2024 4,170 0 View

Following click reaction in cell lysates, protein is immobile and remains at the top of the gel in SDS-PAGE?

I am using CuBr/THPTA for a click reaction in total cell lysates. I am facing issues with my protein sample in non-reducing SDS-PAGE where it's not migrating properly and most of it remains at the...

29 July 2024 950 4 View

How to use energy flexibility in inventory modeling?

29 July 2024 2,192 5 View

I want to get updates regarding international law, international trade law, international institutions and human rights etc?

Please send me updates regarding the above-mentioned areas in the question mark?

28 July 2024 5,197 3 View

What is the principle/mechanism behind aging of carbon (graphite) containing refractory mix for isostatically pressed refractories?

The resin bonded carbon containing refractories are aged before use. How time of aging is determined? And mechanism behind aging.

23 July 2024 3,205 0 View

How to remove cell debris after tissue dissociation?

I'm facing issues with the tumor dissociation protocol for GBM. I use collagenase/dispase with DNase to dissociate my tumor sample. However, even after incubating it for 60mins, I do not get a...

22 July 2024 412 3 View

What methods can be used to minimize environmental variability in breeding trial ?

In breeding trials, environmental variability can significantly affect the results, making it challenging to accurately evaluate the performance of different lines and hybrids.

22 July 2024 3,961 4 View

Is profit margin a good variable to measure the market power of a company?

I have read papers where markup has been taken to measure market power. However, if markup data is unavailable, is it okay to continue with profit margin, as when a company has market power, it...

22 July 2024 707 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

What are the current challenges and future prospects of integrating artificial intelligence into recognition systems for autonomous vehicles?

This question aims to explore the intersection of artificial intelligence and autonomous vehicle technology. It seeks to identify the key challenges faced in implementing AI for recognition...

20 July 2024 3,469 2 View

Recommendations for Rapid Publication Journals in Traffic and Transportation?

I am currently working on a research paper focused on the control of Connected and Autonomous Vehicles (CAVs) utilizing multi-agent reinforcement learning methods. At this stage, I am seeking a...

14 July 2024 2,620 2 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

Is Vacation Homes and Vehicle Rentals in India succesful?

Assessing the Feasibility of Vacation Homes and Vehicle Rentals in India In my article, "Assessing the Feasibility of Vacation Homes and Vehicle Rentals in India: Understanding Market Needs,...

03 July 2024 5,535 1 View