Hello dear researchers
How can I calculate ground temperature and after that how can I find temperature distribution along borehole wall?
kind regards
Hello dear friends Can we assume thermally fully developed flow for a flow in a duct with constant wall temperature? It is assumed there is transient energy equation that means temperature varies...
02 March 2018 2,046 1 View
Hello dear friends What is the conditions that we can assume that we have thermally fully developed flow for both laminar and turbulent flows? I mean can we assume that we have thermally fully...
10 November 2017 8,996 8 View
Hello dear friends There is two channels that one of them is finned and another one is simple and without fin(as attached file). The fluid mass flow rates and inlet fluid temperatures in both...
10 November 2017 5,630 7 View
Hello dear friends What is your idea to solve energy equation analytically in a channel with cyclic boundary condition along the channel that its amplitude is variable? Is it doable?(Please find...
09 October 2017 9,054 7 View
Hello dear friends I have a PDE problem(attached file) with its boundary and initial conditions. Could you please give me your opinion and methods about solving it?
02 March 2017 2,463 53 View
hi friends The attached file is MATLAB code for solar irradiation on tilted surface. Why for latitude=60 and surface angle=60, total irradiation at the night (e. g. 1 or 2), is positive but it...
31 December 2016 9,994 0 View
Hi I did my NN project and target and output results were close to each other but when I calculate Output=W2*(TANSIG(W1*X+B1))+B2, that X is my input, then output is not equal to target. Please...
09 October 2016 9,991 1 View
what should be the flow situation for locating pressure and velocity probe? I mean what should be the boundary layer situation for having the best place to locate these probes? regards
01 February 2015 5,464 5 View
I have modeled my geometry and blocked it in ICEM as attached file. The problem is that I cannot have a good meshing since determinant 2*2*2 says.
04 May 2014 3,392 12 View
I want to model a compressible flow with Ma~0.8 in a pipe in ANSYS CFX.
02 March 2014 5,851 3 View
How to develop investments in renewable energy sources?
08 August 2024 5,112 3 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hi, I'm currently working on a project where I need to plot the atom-projected band structure using GPAW. I've been able to calculate the band structure for my material, but I'm having trouble...
07 August 2024 269 3 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
I am planning to collect human fecal samples for metatranscriptomic analysis using MGI. These samples are from indigenous people living in a region with high temperatures. I will have access to a...
06 August 2024 1,367 3 View
During low-temperature testing, new diffraction peaks that appear could be indicative of several phenomena. In one of our tests, we observed notable new peaks around 40° and 45° in a specific...
06 August 2024 726 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
Is it possible to conduct a molecular dynamics simulation to see the effects of a specific carbohydrate on the structure of lipids (e.g., micelle structure)? I am a beginner in this field and plan...
03 August 2024 3,371 3 View
i have to study the awareness and adoption level of cloud computing in a district of India. i also want to use association among demographic variables like gender, age, education, income etc and...
02 August 2024 2,420 3 View