Hi
I did my NN project and target and output results were close to each other but when I calculate Output=W2*(TANSIG(W1*X+B1))+B2, that X is my input, then output is not equal to target. Please help me what is the problem
regards
Dear Masoud Mohammadian,
Look the link, may be useful.
https://www.youtube.com/watch?v=QU-dnb12eRg
http://lab.fs.uni-lj.si/lasin/wp/IMIT_files/neural/NN-examples.pdf
Regards, Shafagat
Hello dear friends Can we assume thermally fully developed flow for a flow in a duct with constant wall temperature? It is assumed there is transient energy equation that means temperature varies...
02 March 2018 1,943 1 View
Hello dear friends What is the conditions that we can assume that we have thermally fully developed flow for both laminar and turbulent flows? I mean can we assume that we have thermally fully...
10 November 2017 8,745 8 View
Hello dear friends There is two channels that one of them is finned and another one is simple and without fin(as attached file). The fluid mass flow rates and inlet fluid temperatures in both...
10 November 2017 5,540 7 View
Hello dear friends What is your idea to solve energy equation analytically in a channel with cyclic boundary condition along the channel that its amplitude is variable? Is it doable?(Please find...
09 October 2017 8,886 7 View
Hello dear researchers How can I calculate ground temperature and after that how can I find temperature distribution along borehole wall? kind regards
02 March 2017 2,104 0 View
Hello dear friends I have a PDE problem(attached file) with its boundary and initial conditions. Could you please give me your opinion and methods about solving it?
02 March 2017 2,363 53 View
hi friends The attached file is MATLAB code for solar irradiation on tilted surface. Why for latitude=60 and surface angle=60, total irradiation at the night (e. g. 1 or 2), is positive but it...
31 December 2016 9,902 0 View
what should be the flow situation for locating pressure and velocity probe? I mean what should be the boundary layer situation for having the best place to locate these probes? regards
01 February 2015 5,331 5 View
I have modeled my geometry and blocked it in ICEM as attached file. The problem is that I cannot have a good meshing since determinant 2*2*2 says.
04 May 2014 3,283 12 View
I want to model a compressible flow with Ma~0.8 in a pipe in ANSYS CFX.
02 March 2014 5,760 3 View
Hello, Could you please share any interesting research explaining how to choose the number of hidden layers and nodes per layer in case of regression problems using ANN? Thank you, any help would...
01 March 2021 6,200 3 View
Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...
28 February 2021 7,882 2 View
Hi, We culture neural progenitor cells in T175 culture flasks coated with PLO-Laminin. We have successfully grown these cells with our protocol for months. Recently, we observed large sheets...
25 February 2021 3,443 4 View
I am working on creating deep neural network on geospatial dataset and wanted to know how to do the sampling so that I can increase the presence of solar panels in the images. I cannot use entire...
25 February 2021 3,936 6 View
Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...
23 February 2021 6,383 3 View
When I run the job for TS(QST3) in gaseous phase, it was completed without any error. But when I add water in CPCM model it terminated with an error: Inconsistency: ModMin= 2 Eigenvalue=...
21 February 2021 3,198 2 View
Hi all, I have a question regarding calculations using the Pfaffl method. I have 3 groups per experiment: 1 control group (calibrator) and 2 treatment groups with 6 to 7 biological repeats per...
19 February 2021 8,351 2 View
Dear scholars, I was wondering if there are any scientific methods to train a neural network or ANFIS when one of the input variables is stochastic (random) and more importantly non-measurable?...
17 February 2021 1,909 3 View
Are there papers that talk about the possible advantages and disadvantages of using autoencoders instead of CNNs for feature extraction in neural network?
15 February 2021 6,952 3 View
The data collected from various measurement devices often contains erroneous values - such as noise, missing values, etc. What are the popular techniques for pre-processing measurement data in...
14 February 2021 4,642 2 View