19 February 2018 3 5K Report

Can anyone recommend me a good and comprehensive book/article on stochastic domain growth?

More Nico Scheerlinck's questions See All
MSc Project on Cybersecurity Recommendations?

Hi everyone, I'm starting with my project for my master's degree in cyber security and unfortunately, I'm having a hard time coming up with optional topics. I started discussing a a topic on the...

03 June 2024 2,090 4 View

Is it okay to compare the different result of different organisms in Minimum Inhibitory Concentration? or not since they're not the same?

The organism we used are Saccharomyces cerevisiae and Candida tropicalis. In the disk diffusion Candida tropicalis produce inhibition with 5mm but in Saccharomyces cerevisiae has 0 inhibition. But...

30 May 2024 1,349 0 View

My mic (minimum inhibitory concentration) results are all negative, should i still compute the inhibition rate of the concentration?

this is about my thesis, testing the plant extracts against fungal pathogens but unfortunately all the results are negative

25 May 2024 401 4 View

Is there a theory about the study of AI?

theoretical framework

10 March 2024 2,091 3 View

What analyses should I perform (in spss) on my pretest data to select products for my main study?

...

06 June 2023 7,355 4 View

How to perform a mediation analysis for a mixed design study?

I am fairly new to mediation analysis and have a question regarding the type of analysis I need to go for in the following design: Basically, my study has a mixed design. I have a two-level X as...

05 October 2022 2,890 4 View

Why are my Cyclic voltammetry results changing between measurements?

I am trying to detect Calcium in PBS. I am use an Ag/AgCl reference electrode, glassy carbon working electrode and platinum wire counter electrode. I am using PBS pH 8.5 with 0.5 MgCl2 as the...

23 May 2022 1,342 8 View

AFM Nanoscope III distorted image issues?

Has anybody run into similar issues with regards to the Nanoscope III where, when scanning, the image is seemingly elongated as seen in the image below? Having run through the manual and other...

18 April 2022 6,365 10 View

Is carbon paste the best working electrode to use for detection of small biological molecules on a microfluidic device?

I am trying to build an electrochemical sensor for detecting a metabolite produced by yeast, through an engineered pathway. I found a protocol for detecting ethanol using alcohol dehydrogenase, in...

03 February 2022 6,927 0 View

How send parallel port commands using HTML/JS/PHP?

We have an experiment coded in HTML/JavaScript, for which we would like to add EEG triggers via a parallel port. After quite some Google searching, I am impressed how complicated it seems to set...

18 April 2021 5,696 1 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Do you know any references for analyzing stochastic fiber orientaion composites ?

Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...

04 August 2024 3,461 3 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close