Can random sampling have inclusion criteria?

As random sampling means that everyone in the population have an equal chance to be chosen, can it have inclusion criteria? My research participants have been chosen based on the inclusion...

26 February 2021 6,905 10 View

Hye All, Greetings, How can i get surface run off water data?

this is for my thesis project, so this is the title of my thesis, the effect of land use on hydrological components in Muar, Johor, Malaysia any ideas, guidance, and suggestions all? Thank You, :)

02 February 2021 265 5 View

What is the difference of FTIR for functional properties and structural properties of protein?

I need to send my sample to outsource laboratory and how can i tell them that i want to run the FTIR for structural properties of protein? is there any differenece between FTIR for functional...

15 January 2021 8,992 1 View

What's the correct way of treating ordinal variable as continuous in regression?

08 January 2021 920 16 View

Does low pHPZC (Zero point charge) indicates higher negative charged surface ?

I found that, there is a difference in pHPZC value when higher impregnation ratio of acid on adsorbent surface. Lower pHPZC value when higher ratio of acid impregnation and adsorption performance...

05 January 2021 7,224 3 View

Why do I see many vacuoles on my cancer cells?

I am currently growing BICR31 cancer cells for conditioned media collection, and as I passaged it I have seen many bubbles/vacuoles - like structures. Cells were healthy during the first split...

05 January 2021 2,320 5 View

How can be the Virus COVID-19 become mutation?

The current situation the virus become mutation, but there were information that zero percent case in Wuhan?

31 December 2020 2,457 4 View

Why does activation process called as activation? what does the term means actually?

I'm referring to activated carbon activation. Activation process does increase the surface area and functional groups content in activated carbon compared to biochar and raw biomass. But I'm...

30 December 2020 6,514 1 View

What is the good water absorption value for construction materials (brick, mortar etc.)?

According to many construction standards such as ASTM, a good construction material should have a water absorption value within 20%. However, if we compare with many water absorption values (from...

26 November 2020 8,538 8 View

What sample extraction/ preparation needed prior HPLC test?

I want to screen the presence of plastic additives in a few water samples using HPLC-UV. I am very new to HPLC, and after doing a reading on the sample preparation for HPLC, I found there are a...

19 November 2020 2,724 4 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

How to check the uv-vis absorption of nanoparticle by surface plasmon resonance?

I try to check the uv-vis absorption of Indium nanoparticle. Now I am measuring in solution, can I measure it in the form of a film?

01 March 2021 930 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to prepare a thin polymer film by post-polymerization/crosslinking?

24 February 2021 2,362 5 View

How to delaminate copper in water-based anodes?

Hello everyone, I'm looking for a way to delaminate copper current collector of water-based anodes in Li-ion batteries without damaging the graphite film. I tried different materials such as HNO3...

24 February 2021 3,785 3 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

How to improve the adhesion between germanium and silicon monoxide thin film layers using EBEAM evaporation?

I want to deposit multilayer coating of germanium and silicon monoxide on silicon wafer using ebeam evaporation?

21 February 2021 2,141 3 View

How can I measure the thickness of thin layers deposited on textured glass susbtrates?

I want to measure the thickness of aluminum oxide and titanium oxide layers deposited on textured glass substates. The layer thicknesses are typically below 100nm.

21 February 2021 5,465 4 View

How can I retrieve FASTA sequence from gene ID or UID of a Gene ? I have GeneBank IDs ?

I treid to use Entrez Batch, but it redirects me to NCBI site. Is there any script of Linux or Python through which I can download Fasta sequence of list of gene ID ?

21 February 2021 7,783 12 View