Hello,
I am looking at studies where the concentrations of different PCB congeners are listed in pristine soil, in order to determine if the composition of PCBs in non-polluted soils is fixed.
Thanks
Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?
03 March 2021 1,763 2 View
I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...
03 March 2021 2,297 3 View
03 March 2021 8,272 1 View
Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...
03 March 2021 2,037 3 View
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).
03 March 2021 7,100 1 View
03 March 2021 5,360 2 View
The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...
03 March 2021 4,107 4 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
02 March 2021 5,204 3 View
Dealing with a helix antenna, made with flexible material and not rigid like using a PCB board or wire. At the beginning of the helix is too close to the ground plane, causing coupling. How can I...
21 February 2021 4,453 3 View
I would like to plating Ni/Au on the selected area. Can anyone give me a suggestion? It is a bit like to make golden finger on PCB board. Instead with the PCB board, I use polyimide as my...
28 January 2021 8,330 1 View
While feeling the shared pain of costly and slow PCB Manufacturing process. Which also makes the hardware creativity and education much costly and slow. I was trying to figure out how can we...
14 December 2020 1,484 1 View
I am trying to extract the stray inductance of a PCB bus bar using ANSYS Q3D. I tried different types of meshes but every time in the middle of the simulation, this error "Surface Mesh Generation...
10 September 2020 2,060 3 View
How I can made arduino and camera for Defect Detection PCB by image processing system matlab ? please help me thanks
05 September 2020 1,976 5 View
For designing a sensor to be embedded in concrete, which substrates (for example any polymer such as PVC etc) are suitable for long-term measurements. Also please mention if there is any specific...
24 August 2020 4,793 1 View
I want to know about the type of polymers in PCBs.
25 May 2020 9,640 15 View
High amp power electronics devices such as KBPC1006 are connected to the whole circuit using female Faston connectors. My question is what is the proper female connector for other high amp devices...
17 February 2020 366 3 View
I have designed a microstrip patch antenna that has a dimension of 13 mm X 8 mm. The microstrip line width is around 500 micrometers. The substrate is not PCB or FR4, for some reason, I can not...
10 February 2020 7,478 6 View
I have come across screen printing and flexible thin film PCB. in search of Cu alloys or Al alloys and their thickness that makes it flawless over bending tests.
01 February 2020 1,740 3 View